MacDon M150 SP - Manual (Page 47)

OPERATOR’S STATION
Form 169017 / 169087 / 169095
45
Revision C
DETAILED PROGRAMMING INSTRUCTIONS
(Key On / Engine Running or Not / Header Disengaged).
(Press
PROGRAM and SELECT on CDM to enter programming mode).
NOTE: ENGINE MUST BE RUNNING TO CALIBRATE SENSORS.
(continued next page)
L1 D x x x || T R A C T O R S E T U P ?
L2 C x x x || N O / Y E S C A B D I S P L A Y S E T U P ?
L1 C x x x || S E T K N I F E S P E E D ?
L2 M x x x || 1 2 0 0 S P M
L1 C x x x || K N I F E O V E R L O A D S P D ?
L2 M x x x || 1 0 0 0 S P M
or
L1 C x x x || D I S K O V E R L O A D S P D ?
L2 M x x x || 2 0 0 0 R P M
L1 C x x x || O V E R L O A D P R E S S U R E ?
L2 M x x x || 4 0 0 0 P S I
L1 C x x x || H E A D E R I N D E X M O D E ?
L2 M x x x || R E E L & C O N V E Y O R
L2 M x x x || R E E L O N L Y
L1 C x x x || R E T U R N T O C U T M O D E ?
L2 M x x x || H E I G H T & T I L T
L2 M x x x || H E I G H T O N L Y
L1 C x x x || A U T O R A I S E H E I G H T ?
L2 M x x x || - 4 . 0 +
L2 M x x x || - O F F +
L1 C x x x || D W A I N S T A L L E D ?
L2 M x x x || N O / Y E S H E A D E R C U T W I D T H ?
L1 C x x x || S W A P D W A C O N T R O L S ?
L2 M x x x || N O / Y E S
L1 C x x x || D W A A U T O U P / D O W N ?
L2 M x x x || N O / Y E S
L1 C x x x || T I L T C Y L I N S T A L L E D ?
L2 M x x x || N O / Y E S H E A D E R C U T W I D T H ?
L1 C x x x || D I S C B L K I N S T A L L E D ?
L2 M x x x || N O / Y E S H E A D E R C U T W I D T H ?
L1 C x x x || H D R C U T W I D T H ? 0 1 0 1
L2 M x x x || 2 0 . 5 F E E T
L1 C x x x || H A Y C O N D I T I O N E R ?
L2 M x x x || N O / Y E S
L1 C x x x || A U G E R H D R R E E L S P D
L2 M x x x || R P M / M P H
L2 M x x x || R P M / K P H
L1 C x x x || S E T T I R E S I Z E ?
L2 M x x x || 1 8 . 4 X 2 6 T U R F
L2 M x x x || 1 8 . 4 X 2 6 B A R
L2 M x x x || 2 3 . 1 X 2 6 T U R F
L2 M x x x || 6 0 0 - 6 5 R 2 8
L2 M x x x || 5 8 0 / 7 0 R 2 6 T U R F
L1 C x x x || S E T E N G I N E I S C R P M ?
L2 M x x x || N O / Y E S S E T C O N T R O L L O C K S ?
L1 C x x x || P R E S S H A Z A R D T O S E T
L2 M x x x || I S C R P M O F F
L1 C x x x || P R E S S H A Z A R D T O S E T
L2 M x x x || I S C R P M 2 0 0 0
L1 C x x x || P R E S S H A Z A R D T O S E T
L2 M x x x || I S C R P M 1 9 0 0
L1 C x x x || P R E S S H A Z A R D T O S E T
L2 M x x x || I S C R P M 1 8 0 0
Programming Menu Flow Chart
Appears for M150 ONLY - If "NO" then jump to:
Pressing "SELECT" will go to the next line 1
(L1) menu selection. The turn signal "arrow"
keys are used to change the values.
If "NO" then jump to:
AUGER HEADER ONLY
For IMPERIAL display.
This is used to set the Intermediate Speed
Control function for the engine. The default or
last selected rpm will be displayed first and will
be flashing.
The "arrow" keys are used to cycle between
the selections. When "SELECT" is pressed the
program goes to the EXIT ENGINE ISC? menu
selection.
For METRIC display.
If "NO" then jump to:
If "NO" then jump to:
Use the "arrow" keys to set the header cut
width. The header ID appears at the RHS.
DRAPER HEADER ONLY. Default will be
flashing. Use "arrow" keys to select.
If "NO" then jump to:
Swaps the GSL reel fore / aft with the DWA console
controls. If NO jump to DWA AUTO UP & DOWN?
When the programming mode is entered the
header ID will be displayed on the top line of
the CDM using the last 4 display positions.
Pressing "SELECT" will go to the next line 1
(L1) menu selection. The turn signal "arrow"
keys are used to change the values. Pressing
"PROGRAM" at any time will cancel the
programming mode / menus and return back
to the main operating displays.
The auto raise setting can be changed from
4.0 (min.) to 10.0 (max.) in 0.5 increments
OFF disables the auto raise function.
Enables the express up and down feature with the
header RTC. If NO jump to HEADER CUT WIDTH?