MacDon M150 SP - Manual (Page 50)

OPERATOR’S STATION
Form 169017 / 169087 / 169095
48
Revision C
(continued next page)
L2 C x x x || T O C A L I B R A T E S E L E C T
L2 M x x x || H E A D E R H E I G H T
L2 M x x x || H E A D E R T I L T
L1 M x x x || H E A D E R F L O A T
L2 M x x x || E X I T C A L ? N O / Y E S T O C A L I B R A T E S E L E C T
L1 C x x x || D I A G N O S T I C M O D E ?
L2 M x x x || N O / Y E S T R A C T O R S E T U P ?
L1 C x x x || V I E W E R R O R C O D E S ?
L2 M x x x || N O / Y E S E N T E R S E N S O R S E T U P ?
L1 C x x x || V I E W T R A C T O R C O D E S ? ||
L2 M x x x || N O / Y E S V I E W E N G I N E C O D E S ?
L1 1 || 1 2 3 4 . 5 H R S 1 2 3 ||
L2 E 4 7 || S E N S O R V O L T S L O W
L1 2 || 1 2 3 0 . 5 H R S 1 2 3 ||
L2 E 7 1 || L O W H Y D R A U L I C O I L
L1 C x x x || E X I T T R A C T O R C O D E S ?
L2 M x x x || N O / Y E S
L1 C x x x || V I E W E N G I N E C O D E S ?
L2 M x x x || N O / Y E S E N T E R S E N S O R S E T U P ?
L1 1 || 1 2 3 4 . 5 H R S 1 2 3 ||
L2 4 4 9 || F U E L P R E S S U R E H I G H
L1 C x x x || E X I T E N G I N E C O D E S ?
L2 M x x x || N O / Y E S
L1 C x x x || E X I T E R R O R C O D E S ?
L2 M x x x || N O / Y E S V I E W T R A C T O R C O D E S ?
L1 C x x x || E N T E R S E N S O R S E T U P ?
L2 M x x x || N O / Y E S R E A D S E N S O R I N P U T S ?
L1 C x x x || K N I F E S P E E D S E N S O R
L2 M x x x || E N A B L E / D I S A B L E
L1 C x x x || R E E L S P E E D S E N S O R
L2 M x x x || E N A B L E / D I S A B L E
L1 C x x x || H E A D E R H T S E N S O R
L2 M x x x || E N A B L E / D I S A B L E
L1 C x x x || H E A D E R T I L T S E N S O R
L2 M x x x || E N A B L E / D I S A B L E
L1 C x x x || H E A D E R F L O A T S E N S O R
L2 M x x x || E N A B L E / D I S A B L E
L1 C x x x || O V E R L O A D P R E S S U R E
L2 M x x x || E N A B L E / D I S A B L E
L1 C x x x || H Y D O I L T E M P S E N S O R
L2 M x x x || E N A B L E / D I S A B L E
L1 C x x x || E X I T S E N S O R S E T U P ?
L2 M x x x || N O / Y E S K N I F E S P E E D S E N S O R
L1 C x x x || R E A D S E N S O R I N P U T S ?
L2 M x x x || N O / Y E S A C T I V A T E F U N C T I O N S ?
L1 C x x x || S E N S O R I N P U T
L2 M x x x || H D R H E I G H T 3 . 5 9 V
L1 C x x x || S E N S O R I N P U T
L2 M x x x || H D R A N G L E 1 . 8 4 V
L1 C x x x || S E N S O R I N P U T
L2 M x x x || 2 . 4 5 V F L O A T 2 . 8 4 V
L1 C x x x || S E N S O R I N P U T
L2 M x x x || K N I F E S P E E D 1 2 3 H Z
L1 C x x x || S E N S O R I N P U T
L2 M x x x || R E E L S P E E D 1 2 3 H Z
If "NO" then jump to:
If "NO" then jump to:
The last 10 distinct error codes are stored.
The operator can select each sensor and
selectively enable or disable the sensor. This
can be used to disable a failed sensor to
eliminate false or erratic display readings.
If "NO" then jump to:
Select any of the sensors by using the turn signal switches to
cycle through the choices. Pressing SELECT will take the
operator to the calibration menu for that particular sensor. NO
is the default for EXIT CAL?. If "NO" then jump to:
If "NO" then jump to:
If "NO" then jump to:
If "NO" then jump to:
The last 10 distinct error codes are stored
along with the code #, Exxx, engine hours and
number of occurrences. The "arrow" keys are
used to cycle between codes.
If "NO" then jump to the first error code logged.
If "NO" then jump to the first engine error code
logged.
For diagnostic purposes each sensors input
signal can be read. This helps in determining
how each sensor is operating and if the proper
output voltages are being received by the
control system.
If "NO" then jump to:
If "NO" then jump to:
When "SELECT" is pressed the program goes
to the EXIT SENSOR SETUP? menu
selection.
NOTE: The oil temp. readout applies to the
M205 model with the Sensata oil temp. sensor.