Metrohm 732 IC Detector - Manual (Page 222)

7.5 Index
732 IC Detector / 733 IC Separation Center
215
Sample pretreatment cartridge
IC-OH ............................................ 201
Sample pretreatment cartridge
IC-RP ............................................. 200
Screw nut 97 97
Figure ............................................ 142
Mounting ....................................... 144
Seiko printer DPU-411/414............. 42,90
<SELECT>.................................... 76,79
SELECT ................................................. 86
Select event....................................... 116
Select preset parameter values........... 76
Select program steps........................ 109
Select status message ........................ 76
Selection of data.................................. 79
Selection of the
character set/printer type ................ 90
Selection of the method ............. 117,118
Selection of the report ....................... 124
Selection of the sample loop............... 32
Selectivity........................................... 133
send to ............................................... 90
Sensitivity............................................. 98
Separating column
Changing....................................... 138
Characteristic data ........................ 133
Dead volume ................................. 134
Fixing .......................................... 35,37
General information......................... 32
Installation .................................. 35,37
Ordering designations................... 198
Practical notes............................... 133
Protection ...................................... 133
Regeneration ................................. 134
Rinsing........................................ 35,37
Separation efficiency ..................... 133
Storage.......................................... 133
Separation efficiency......................... 133
Serial number ................. 90,119,122,149
Serial number 10
10
Figure ................................................ 4
Serial/parallel converter
(2.145.0300) ........................ 43,44,202
Service........................................ 136,159
Servicing............................................ 136
Setting up the instruments................... 12
Settings
709 IC Pump.................................. 101
733 IC Separation Center ................ 95
Analog output .................................. 99
Beeper ............................................. 92
Conductivity detector.................. 88,97
Events.............................................. 92
External printer ................................ 89
Graphics plot................................. 100
Injection valve A............................... 95
Injection valve B............................... 96
Mains voltage .................................. 17
Measured value printout.................. 90
Peripherals....................................... 87
Remote output lines......................... 84
RS232 interface ............................... 93
Suppressor module......................... 96
Setup ................................................... 84
SETUP/graphics ................................. 86
SETUP/input assign ......................... 85
SETUP/output ..................................... 84
SETUP/peripherals ........................... 87
Shutdown .......................................... 137
Shutoff limits................................... 82,83
Sign change ........................................ 75
Silicone tubing (6.1816.000) ............. 194
Single-channel system ................ 2,35,37
Software handshake
with character stop........................ 179
Software handshake
with line stop ................................. 180
SOP................................................... 159
Spilled chemicals .............................. 136
Splitting ...................................... 134,148
Standard chromatogram................... 133
Standard equipment ......................... 193
Standard operating procedures........ 159
Standard solution ................................ 59
Standby mode........................... 71,73,81
Start graphics plot............................... 75
Start measured value output ............... 75
Start of a program ............................. 114
Start report output ............................... 75
Start the graphics plot....................... 122
Start/stop program....................... 73,115
Start/stop pump drive ........... 74,106,112
Static charges ..................................... 10
status ................................ 92,95,96,108
Status messages................ 49,71,82,164
Status messages for 709 IC Pump ..... 82
Status messages for method .............. 82
Status messages for program step..... 83
Status of the beeper............................ 92
Steel capillary 71
71
Connection...................................... 25
Figure .............................................. 26
Steel capillary (6.2620.020).......... 19,194
Steel connector 79
79
Figure .............................................. 29
Installation ....................................... 30
Steel connectors ................................. 19
Steel mesh holding end 61
61
Figure .............................................. 23
Installation ....................................... 23
Steel meshes 60 60
Figure ......................................... 23,29
Installation ....................................... 23
Ordering designation .................... 197
Steel meshes 73 73
Figure .............................................. 29
Installation .................................. 28,30
Ordering designation .................... 197
Steel spacer 78 78
Figure .............................................. 29
Installation ....................................... 30
Ordering designation .................... 197
step .............................................. 96,112
Stirring of the eluent .......................... 135
stop bit ........................................ 93,94
Stop of a program........................ 73,114
stop time ............................. 91,100,121
Stop time for graphics plot................ 100
Stop time for
measured value printout.................. 91
stopped ................................... 82,83,101
Store method................................ 64,118
Submenu................................... 54,71,77
Sunlight ............................................... 12
Suppression ........................................ 33
suppressor ....................................... 112
Suppressor holder 100 100
Figure ......................................142,143
Mounting ........................................144
Suppressor inlet capillary 89 89
Figure ..........................................36,38
Installation ........................................37
Suppressor inlet capillary 90 90
Figure ..........................................36,38
Installation ........................................38
Suppressor inlet capillary 93 93
Figure ..........................................37,38
Installation ........................................39
Suppressor module 95 95
Cleaning.........................................141
Conditioning.....................................40
Connection 1....................................37
Connection 2....................................38
Connection 3....................................39
Connection of column......................37
Display of position............................96
Figure ...............................................37
General information..........................33
Installation ........................................37
Protection .......................................136
Regeneration..................................140
Replacement..................................143
Rotation............................................76
Settings ............................................96
Switching............................96,103,112
Suppressor outlet capillary 91 91
Figure ..........................................37,38
Installation ...................................38,39
Suppressor outlet capillary 92 92
Figure ..........................................37,38
Installation ........................................39
Suppressor outlet capillary 94 94
Figure ..........................................37,38
Installation ........................................37
Suppressor rotor 99 99
Cleaning.........................................143
Figure .............................................142
Inserting .........................................143
Ordering designation .....................201
Replacement..................................143
Switch off auto-zero ......................74,106
Switch off data receipt .........................93
Switch on data receipt .........................93
Switching of the
suppressor module.....96,103,104,112
Switching of the valve .....................95,96
Switching to "FILL"................................76
Switching to "INJECT" ..........................76
Syringe (6.2816.020)
Connection of syringe ......................16
Ordering designation .....................195
T
Technical data....................................189
temp.coeff. ........................................99
Temperature coefficient ...........55,99,189
Temperature correction......................189
Temperature dependence ............99,189
Temperature deviation .......................190
Temperature of conductivity cell ..........88
Temperature stability.....................88,190
Terminal block 38
38
Figure .................................................7
Pin assignment...............................188