Panasonic TH-55VF2HW 54.6" Full HD Video Wall Display - Manual (Page 11)

11
English
Precautions for use
When unpacking
• The package of this product includes the unit and
supplied accessories.
• Check all accessories are included. (see page 13)
Cautions when installing
Do not set up the Display outdoors.
• The Display is designed for indoor use.
Install this unit at a location which can support the
weight of the unit.
• Dropping or falling of the unit may cause injury.
• Use the installation mount that conforms to VESA
standards.
Environmental temperature to use this unit
• When using the unit where it is below 1 400 m
(4 593 ft) above sea level: 0 °C to 40 °C (32 °F to
104 °F)
• When using the unit at high altitudes (1 400 m
(4 593 ft) and higher and below 2 800 m (9 186 ft)
above sea level): 0 °C to 35 °C (32 °F to 95 °F)
Do not install the unit where it is 2 800 m (9 186 ft)
and higher above sea level.
• Failure to do so may shorten the life of the internal
parts and result in malfunctions.
We are not responsible for any product damage, etc.
caused by failures in the installation environment
even during the warranty period.
Transport only in upright position!
• Transporting the unit with its liquid crystal panel
facing upright or downward may cause damage to the
internal circuitry.
Do not place the display where it may be affected by
salt or corrosive gas.
• Failure to do so may shorten the life of the internal
parts and result in malfunctions due to corrosion.
Do not install the product to a place where the
product is exposed to direct sunlight.
• If the unit is exposed to direct sunlight even indoors,
the temperature rise of the liquid crystal panel may
cause malfunction.
Required space for ventilation
• For the outermost periphery of the display, leave a
space of 10 cm (3.94”) or more at the top, bottom, left
and right.
At the rear, leave a space of 5 cm (1.97”) or more.
• Operation of this unit is guaranteed up to an ambient
temperature of 40 °C (104 °F). When installing the
unit in a case or chassis, be sure to provide adequate
ventilation with a cooling fan or ventilation hole so
that the surrounding temperature (inside the case or
chassis) including the temperature of the front surface
of the liquid crystal panel can be kept at 40 °C
(104 °F) or less.
About the screws used for the mounting bracket that
conforms to VESA standards
Screw pitch for
installation
Depth of
screw hole
Screw
(quantity)
400 mm × 400 mm 12 mm M6 (4)
Installing multi displays
• When installing multiple displays, the LCDs may
dilate due to temperature change inside the main unit,
resulting in malfunction.
Considering this, provide a gap of 0.5 mm or more
between displays for installation.
For details of how to install, visit the following web
site.
(https://bizpartner.panasonic.net/public/ppr/file_
view/187616)
Do not grab the liquid crystal panel.
• Do not forcibly press the liquid crystal panel, or push
it with a pointed object. Applying a strong force to
the liquid crystal panel will cause unevenness of the
screen display, resulting in malfunction.
When using
Red, blue or green dots on the screen are a liquid
crystal panel-specific phenomenon. This is not a
malfunction.
• Although the liquid crystal display is manufactured
with high-precision technology, always-lighting dots or
non-lighting dots may appear on the screen. This is
not a malfunction.
The ratio of dot omission is 0.00013% or less.
* 1
* 1: Calculated in sub-pixel units according to the
ISO09241-307 standard.
Depending on the temperature or humidity
conditions, uneven brightness may be observed.
This is not a malfunction.
• This unevenness will disappear while applying current
continuously. If not, consult the distributor.