Initial setting – Sharp AR-M162 User Manual
Page 225
96
KEY OPERATOR PROGRAMS
2
Select "LIST PRINT/SET" with the [
] or
[
] key and then press the [OK] key.
3
Select "LIST SETTING" with the [
] or [
]
key and then press the [OK] key.
4
Select "AUTO LISTING" with the [
] or
[
] key and then press the [OK] key.
5
Select "AUTO PRINT REPT AT LIMIT (50)"
with the [
] or [
] key and then press the
[OK] key.
• The setting is enabled and a checkmark appears in
the checkbox.
• If this procedure is performed when the setting is
enabled, the checkmark will be cleared and the
setting disabled.
6
If you wish to have the activity report
printed at regular intervals, go to step 7. If
you have finished selecting settings for
this program, press the [BACK] key.
7
Select "PRINT DAILY AT DESIGNATED
TIME" with the [
] or [
] key and then
press the [OK] key.
8
Select "SETTING" with the [
] or [
] key
and then press the [OK] key.
9
Enter the printout time with the numeric
keys and press the [OK] key.
If you make a mistake, move the cursor to the incorrect
digit with the [
] or [
] key (the cursor should be over
the digit), and then enter the correct digit.
INITIAL SETTING
These programs are used to change the default
settings (initially set at the factory) for the various fax
functions to settings that better meet your needs.
PAUSE TIME
This setting is used to select the duration of pauses
that are inserted in destination fax numbers.
Normally the setting is 2 seconds, which means that
each time the [PAUSE] key is pressed when dialling or
storing a fax number, a pause of 2 seconds is inserted.
The pause time can be set to any number of seconds
from 1 to 15.
1
Follow steps 1 through 6 of "INITIAL
PROCEDURE" (page 94).
2
Select "INITIAL SETTING" with the [
] or
[
] key and then press the [OK] key.
3
Select "PAUSE TIME" with the [
] or [
]
key and then press the [OK] key.
4
Enter the pause time in seconds ("01" to
"15") with the numeric keys and then
press the [OK] key.
If you make a mistake, move the cursor to the
incorrect digit with the [
] or [
] key (the cursor
should be over the digit), and then enter the
correct digit.
OWN PASSCODE SET
Use this setting to program the fax number of the
machine and the name of the user. The programmed
name and number are printed at the top of each fax
page you send. The number is also used as a
passcode when performing polling reception "USING
THE POLLING FUNCTION" (page 37).
You can check your programmed name and number
by printing out the "KEY OPE. LIST". (Page 95)
• A maximum of 20 digits can be stored for the fax
number.
• A maximum of 18 letters can be stored for the name.
1
Follow steps 1 through 6 of "INITIAL
PROCEDURE" (page 94).
2
Select "INITIAL SETTING" with the [
] or
[
] key and then press the [OK] key.
3
Select "OWN PASSCODE SET" with the
[
] or [
] key and then press the [OK]
key.
4
Select "STORE" with the [
] or [
] key
and then press the [OK] key.
• After step 9 you will return to step 8. If you
need to change the set time, follow steps
8 and 9 to enter the new time.
• To cancel a "PRINT DAILY AT
DESIGNATED TIME" setting, follow these
steps:
(1) Select "CANCEL" in step 8 and then
press the [OK] key.
(2) Select "CANCEL" with the [
] or [
]
key and then press the [OK] key.
• If "AUTO PRINT REPT AT LIMIT (50)" is
not enabled and the number of recorded
transactions exceeds 50, each new
transaction will delete the oldest
transaction.
• The activity report can also be printed out
on demand. (See "PRINTING LISTS OF
PROGRAMMED INFORMATION,
SETTINGS, AND COMMUNICATION
ACTIVITY" on page 81.)
Note