Recall setting (busy), Recall set (err) – Sharp AR-M162 User Manual
Page 231
102
KEY OPERATOR PROGRAMS
RECALL SETTING (BUSY)
This program is used to set the number of recall
attempts and the interval between recall attempts
when a transmission is not successful due to the line
being busy or other reason.
Normally the machine is set to make 2 recall attempts
at intervals of 3 minutes.
If you do not wish to have recalling take place, set the
number of attempts to "0" (steps 6 and 7).
1
Follow steps 1 through 6 of "INITIAL
PROCEDURE" (page 94).
2
Select "SENDING FUNCTION" with the [
]
or [
] key and then press the [OK] key.
3
Select "RECALL SETTING (BUSY)" with
the [
] or [
] key and then press the [OK]
key.
If you do not wish to change the recall interval setting,
go to step 6.
4
Select "RECALL INTERVAL" with the [
]
or [
] key and then press the [OK] key.
5
Enter the recall interval (01 to 15) with the
numeric keys and then press the [OK] key.
• The recall interval can be set from 1 to 15 minutes.
• After finishing step 5, if you do not wish to change the
number of recall attempts, press the [BACK] key to
exit.
6
Select "RECALL TIMES" with the [
] or
[
] key and then press the [OK] key.
7
Enter the number of recall attempts with
the numeric keys and then press the [OK]
key.
• The number of recall attempts can be set in each
country are shown in the following table.
Country Differentiation Table
• If you do not wish to have recalling take place, set the
number of attempts to "0".
RECALL SET (ERR)
When sending a fax, this setting is used to select
whether or not the machine will automatically
re-attempt the call if the transmission fails due to a line
error. Normally the machine is set to make 1 recall
attempt at intervals of 1 minute.
If you do not wish to have recalling take place, set the
number of attempts to "0" (steps 6 and 7).
1
Follow steps 1 through 6 of "INITIAL
PROCEDURE" (page 94).
2
Select "SENDING FUNCTION" with the [
]
or [
] key and then press the [OK] key.
3
Select "RECALL SET(ERR)" with the [
]
or [
] key and then press the [OK] key.
If you do not wish to change the recall interval setting,
go to step 6.
4
Select "RECALL INTERVAL" with the [
]
or [
] key and then press the [OK] key.
5
Enter the recall interval (00 to 15) with the
numeric keys and then press the [OK] key.
• The recall interval can be set from 0 to 15 minutes.
• After finishing step 5, if you do not wish to change the
number of recall attempts, press the [BACK] key to
exit.
6
Select "RECALL TIMES" with the [
] or
[
] key and then press the [OK] key.
7
Enter the number of recall attempts with
the numeric keys and then press the [OK]
key.
• The number of recall attempts can be set in each
country are shown in the following table.
Country Differentiation Table
• If you do not wish to have recalling take place, set the
number of attempts to "0".
United
Kingdom
Australia and
New Zealand
The number of
recall attempts
0 to 10
0 to 9
• If you made a mistake in step 5 or step 7,
move the cursor to the mistake with the
[
] or [
] key and enter the correct
number.
• Even if this setting is enabled, the
machine will not re-attempt the call when
a fax is sent by manual transmission.
Note
United
Kingdom
Australia and
New Zealand
The number of
recall attempts
0 to 5
0 to 1
• If the recall interval is set to "0", the
machine will immediately call again after
the connection is broken due to the line
error.
• If you made a mistake in step 5, move the
cursor to the mistake with the [
] or [
]
keys and enter the correct number.
• Even if this setting is enabled, the
machine will not re-attempt the call when
a fax is sent by manual transmission.
Note