Rockwell Automation 1395 Digital DC Drive FRN 5-10.10/9.30 - Manual (Page 301)

Index
I-7
Field Current at 7/8 Flux, 684, 7-53
Field Current Feedback
1–30 HP/2–60 HP Drives, 2-5
125–300 HP/250–600 HP Drives, 4-5
40–100 HP/75–200 HP Drives, 3-5
Field Current Feedback, 118, 7-23
Field Current Range Jumper Selections, 1–30 HP/2–60 HP
Drives, 2-9
Field Current Reference, 117, 7-22
Field Economy, 1-4
Field Economy Delay, 675, 7-50
Field Economy Reference, 674, 7-50
Field Failure Delay, 730, 7-65
Field Fault Threshold, 729, 7-64
Field Flux Control, 5-30
Block Diagram, 5-36
Definition, 5-5
Field Flux Reference, 676, 7-51
Field Flux Tune, 5-14, 5-18
Field PI Control, 5-31
Block Diagram, 5-37
Field Pulse Transformer
1–30 HP/2–60 HP Drives, 2-5
125–300 HP/250–600 HP Drives, 4-12
125–300 HP/250–600 HP Drives – Illustration, 4-12
Field Pulse Transformer and Snubber Board
40–100 HP/75–200 HP Drives, 3-5, 3-12
40–100 HP/75–200 HP Drives – Illustration, 3-13
Field Sync and Firing Logic, Definition, 5-6
Field Transformer Connections, 6-18
Field Voltage, 1-4
Output, 6-14
Field Weakened Speed, 686, 7-54
Field Weakening Control, Block Diagram, 5-36
Final Velocity Reference, 104, 7-20
Flux Command, 115, 7-22
Flux Feed Forward, 159, 7-30
Flux Mode Select, 627, 7-39
Flux Trim, 121, 7-23
Forward Bridge Current Limit, 663, 7-48
Forward Speed Limit, 608, 7-33
Functional Description, 5-1
Terminology, 5-1
Fuses, 125–300 HP/250–600 HP Drives, 4-3
G
Gate Firing Pulses, 1–30 HP/2–60 HP Drives, 2-6
Ground (PE), 6-8, 6-10
Grounding
Illustration, 6-9
Procedures, 6-8
Safety Ground Connections, 6-11
Safety/Signal Ground, 6-11
Stand Alone Drive – Illustration, 6-10
System Grounding – Illustration, 6-12
H
Hardware Description
1–30 HP/2–60 HP Drives, 2-1
125–300 HP/250–600 HP Drives, 4-1
40–100 HP/75–200 HP Drives, 3-1
Hardware Overview
1–30 HP/2–60 HP Drives, 2-1
1–30 HP/2–60 HP Drives – Illustration, 2-2
125–300 HP/250–600 HP Drives, 4-2
125–300 HP/250–600 HP Drives – Illustration, 4-2
40–100 HP/75–200 HP Drives, 3-1
40–100 HP/75–200 HP Drives – Illustration, 3-2
I
I/O Checks, Standard Control, 8-8
Incoming Device, 125–300 HP/250–600 HP Drives, 4-3
Indirect Parameters, 5-9
Inductor, 1–30 HP/2–60 HP Drives, 2-5
Input Frequency, 1-4
Max Rate of Change, 1-4
Input Parameters, 8-13
Input Power, 1-4
Input Voltages, 1-4
Interface
1–30 HP/2–60 HP Drives, 2-1
125–300 HP/250–600 HP Drives, 4-1
40–100 HP/75–200 HP Drives, 3-1
Description, 5-1