Rockwell Automation 1395 Digital DC Drive FRN 5-10.10/9.30 - Manual (Page 304)

Index
I-10
External Overtemperature Delay, 725, 7-63
Fault Report, 630, 7-41
Fault Select, 623, 7-37
Feedback Device Type, 621, 7-36
Field Current at 0/8 Flux, 677, 7-51
Field Current at 1.0 Flux, 685, 7-54
Field Current at 1/8 Flux, 678, 7-51
Field Current at 2/8 Flux, 679, 7-52
Field Current at 3/8 Flux, 680, 7-52
Field Current at 4/8 Flux, 681, 7-52
Field Current at 5/8 Flux, 682, 7-53
Field Current at 6/8 Flux, 683, 7-53
Field Current at 7/8 Flux, 684, 7-53
Field Current Feedback, 118, 7-23
Field Current Reference, 117, 7-22
Field Economy Delay, 675, 7-50
Field Economy Reference, 674, 7-50
Field Failure Delay, 730, 7-65
Field Fault Threshold, 729, 7-64
Field Flux Reference, 676, 7-51
Field Weakened Speed, 686, 7-54
Final Velocity Reference, 104, 7-20
Flux Command, 115, 7-22
Flux Feed Forward, 159, 7-30
Flux Mode Select, 627, 7-39
Flux Trim, 121, 7-23
Forward Bridge Current Limit, 663, 7-48
Forward Speed Limit, 608, 7-33
Jog 1 Speed, 638, 7-42
Jog 2 Speed, 639, 7-43
Jog Dwell, 711, 7-60
Jog Ramp Enable, 626, 7-39
K AC Volts, 740, 7-67
K Armature Volts, 739, 7-67
K Discontinuous Fraction, 745, 7-70
K Discontinuous, 734, 7-66
KF Velocity Loop, 661, 7-47
KI Armature Loop, 736, 7-66
KI Field Loop, 738, 7-66
KI Flux, 672, 7-50
KI Velocity Loop, 659, 7-47
Kn Filter, 692, 7-56
KP Armature Loop, 735, 7-66
KP Field Loop, 737, 7-66
KP Flux, 673, 7-50
KP Velocity Loop, 660, 7-47
Logic Command 1, 150, 7-25
Logic Command 2, 151, 7-28
Logic Command 3, 152, 7-29
Logic Status, 100, 7-16
Maintained Start, 624, 7-38
Maximum Current Loop Bandwidth, 742, 7-68
Minimum Tapered Current, 667, 7-49
Mop Accel 1, 641, 7-43 Mop Accel 2, 642, 7-43
Mop Accel 3, 643, 7-43
Mop Accel 4, 644, 7-44
Mop Decel 1, 645, 7-44
Mop Decel 2, 646, 7-44
Mop Decel 3, 647, 7-44
Mop Decel 4, 648, 7-45
Mop Max Speed, 649, 7-45
Mop Min Speed, 650, 7-45
Motor Armature Full Load Amp, 611, 7-34
Motor Inertia, 613, 7-34
Motor Overload Select, 629, 7-40
Overload Pending Level, 720, 7-62
Position Error, 109, 7-21
Position Feedback, 107, 7-21
Pre Ramp Velocity Reference, 102, 7-20
Preset Speed 1, 633, 7-41
Preset Speed 2, 634, 7-42
Preset Speed 3, 635, 7-42
Preset Speed 4, 636, 7-42
Preset Speed 5, 637, 7-42
Process Trim Feedback, 162, 7-31
Process Trim Filter Constant, 713, 7-61
Process Trim High Limit, 718, 7-62
Process Trim High Sum, 722, 7-63
Process Trim KI Gain, 715, 7-61
Process Trim KP, 716, 7-61
Process Trim Low Limit, 717, 7-62
Process Trim Low Sum, 721, 7-63
Process Trim Output Gain, 719, 7-62
Process Trim Output, 119, 7-23
Process Trim PI Input, 125, 7-24
Process Trim Preload, 714, 7-61
Process Trim Reference, 161, 7-31
Process Trim Select, 628, 7-40
Ramp Velocity Reference, 103, 7-20
Rated AC Line Voltage, 617, 7-35
Rated Armature Bridge Current, 615, 7-35
Rated Field Bridge Current, 616, 7-35
Rated Field Motor Current, 612, 7-34
Rated Motor Voltage, 610, 7-34
Reverse Bridge Current Limit, 664, 7-48
Reverse Speed Limit, 607, 7-33
SCR Overtemperature Delay, 726, 7-64
Slave Percent 2, 670, 7-49
Slave Percent, 669, 7-49
SP Indirect 1, 840, 7-70
SP Indirect 2, 841, 7-71
SP Indirect 3, 842, 7-71
SP Indirect 4, 843, 7-72
SP Indirect 5, 844, 7-72
SP Output 1, 10, 7-15
SP Output 2, 11, 7-15
SP Output 3, 12, 7-15
SP Output 4, 13, 7-15