Rockwell Automation 1395 Digital DC Drive FRN 5-10.10/9.30 - Manual (Page 307)

Index
I-13
125–300 HP/250–600 HP Drives, 4-4
40–100 HP/75–200 HP Drives, 3-4
SCR Snubbers, 125–300 HP/250–600 HP Drives, 4-5
Set Up Parameter, Definition, 7-2
Setting Trend Buffer Output Rate, 5-23
Setting Trend Buffer Type, 5-23
Set-Up Parameters, 8-12
Sink
Definition, 5-2
Parameters, 5-6
Slave Percent 2, 670, 7-49
Slave Percent, 669, 7-49
Source
Definition, 5-2
Parameters, 5-9
Source and Sink Parameters
Partial Illustration, 5-7
Table, 5-8
SP Indirect 1, 840, 7-70
SP Indirect 2, 841, 7-71
SP Indirect 3, 842, 7-71
SP Indirect 4, 843, 7-72
SP Indirect 5, 844, 7-72
SP Output 1, 10, 7-15
SP Output 2, 11, 7-15
SP Output 3, 12, 7-15
SP Output 4, 13, 7-15
SP Output 5, 14, 7-15
Specifications
Electrical, 1-4
Environmental, 1-5
External Inputs, 1-5
External Outputs, 1-5
Feedback Devices, 1-5
Options, 1-5
Speed Regulation, 1-4
Standard Features, 1-5
Speed Reference Parameters, 8-13
Speed Reference Selection, Definition, 5-4
Speed Regulation Specifications, 1-4
Stall Delay, 727, 7-64
Standard Features Specifications, 1-5
Standard Field Voltage
Output, 6-14
Power Connections, 6-15, 6-16, 6-17
Start Taper Speed, 665, 7-48
Start-Up, 8-1
1–30 HP and 2–60 HP Voltage Measurement, 8-6
115VAC Voltage Measurement, 8-5
125–300 HP and 250–600 HP Voltage Measurement,
8-7
24VDC Voltage Measurement, 8-6
40–100 HP and 75–200 HP Voltage Measurement, 8-7
Adapter Parameters, 8-14
Application Setup, 8-22
Basic Parameters, 8-9, 8-11
Bridge Switch Delay, 8-11
Current Loop Test, 8-19
Current Loop Tune, 8-20
Digital Reference Adapter Pre-Configuration, 8-15
Discrete Adapter Pre-Configuration, 8-14
Drive Calibration Verification, 8-17
Drive Configuration, 8-16
Drive Tuning, 8-19
Equipment Recommended, 8-2
Equipment Required, 8-2
Field AC Voltage Measurement, 8-5
Field Flux Tuning, 8-21
Input Parameters, 8-13
Motor and Feedback Polarity Checks, 8-16
Parameter Programming Procedures, 8-8
Pre-Power Checklist, 8-4
Pre-Power Checks, 8-3
Rated Armature Bridge Current, 8-10
Rated Field Bridge Current, 8-11
Sequence Illustrated, 8-3
Set-Up Parameters, 8-12
Speed Reference Parameters, 8-13
Standard Control I/O Checks, 8-8
Tools Recommended, 8-2
Tools Required, 8-2
Velocity Loop Motor Test, 8-20
Velocity Loop System Test, 8-20
Velocity Loop Tuning, 8-21
Voltage Measurement, 8-5
Storing this Drive, 1-3
Supply Voltage
1–30 HP/2–60 HP Drives, 2-5
125–300 HP/250–600 HP Drives, 4-5
40–100 HP/75–200 HP Drives, 3-5
Surge Suppression
1–30 HP/2–60 HP Drives, 2-4, 2-5
125–300 HP/250–600 HP Drives, 4-4, 4-5
40–100 HP/75–200 HP Drives, 3-4, 3-5
Synchronization
1–30 HP/2–60 HP Drives, 2-3