Rockwell Automation 1395 Digital DC Drive FRN 5-10.10/9.30 - Manual (Page 303)

Index
I-9
Motor Connection, 6-8
for CCW Rotation, 6-14
Motor Inertia, 613, 7-34
Motor Operated Pot, 1-5
Motor Overload Select, 629, 7-40
Motor Thermostat, 1-5
Mounting, 6-1
Multi-Communication Adapter Board, 6-40
1–30 HP/2–60 HP Drives, 2-17
125–300 HP/250–600 HP Drives, 4-21
40–100 HP/75–200 HP Drives, 3-22
Specifications, 1-6
N
NEMA Type 12 Enclosures, 6-5
Node Adapter Board, 6-40
1–30 HP/2–60 HP Drives, 2-17
125–300 HP/250–600 HP Drives, 4-21
40–100 HP/75–200 HP Drives, 3-22
Non-Volatile Memory, Definition, 7-2
O
Objectives of this Manual, 1-1
Options
1–30 HP/2–60 HP Drives, 2-14
125–300 HP/250–600 HP Drives, 4-18
40–100 HP/75–200 HP Drives, 3-19
for this Drive, 1-2
Specifications, 1-5
Output
Current, 1-4
Data Rate, 5-25
Horsepower, 1-4
Voltage, 1-4
Waveform, 1-4
Overload Pending Level, 720, 7-62
P
Parameter
Alphabetical Listing, 9-10
Definition, 5-1, 7-2, 8-2
Indirect, 5-9
Internal Configuration, 9-8
Linking Source to Sink, 5-10
Sink, 5-6
Source, 5-9
Trend Buffer, 9-8
Trend Value, 9-8
Parameter Entry, Definition, 7-2
Parameter Programming Procedures
Basic Parameters, 8-9
Start-Up, 8-8
Parameter Table, 7-3
Definition, 5-2, 7-2
Parameter Table Storage, 7-4
Parameter Value List, 9-4
Parameters
1395 Version Number, 780, 7-70
920 to 927, 7-77
930 to 937, 7-77
940 to 947, 7-77
Absolute Overspeed, 724, 7-63
AC Line Tolerance Delay, 728, 7-64
AC Line Voltage, 116, 7-22
Accel Time, 651, 7-45
Armature Bridge Type, 733, 7-65
Armature Current Feedback, 112, 7-22
Armature Current Firing Angle, 114, 7-22
Armature Current PI Output, 113, 7-22
Armature Current Reference, 111, 7-21
Armature Resistance, 614, 7-35
Armature Voltage Feedback, 105, 7-20
Armature Voltage Offset Calibration, 746, 7-70
At Speed 1, 704, 7-58
At Speed 2, 705, 7-59
At Speed 3, 706, 7-59
At Speed 4, 707, 7-59
At Speed 5, 708, 7-60
Auto Tune Current Limit, 698, 7-56
Auto Tune Speed, 699, 7-57
Base Motor Speed, 606, 7-33
Bridge Switch Delay, 744, 7-69
CEMF Feedback, 120, 7-23
CEMF Reference, 160, 7-31
CEMF Reg Preload, 687, 7-54
Contactor Type, 622, 7-37
Current Damping Factor, 743, 7-68
Decel Time, 652, 7-46
Desired Contour, 653, 7-46
Desired Current Loop Bandwidth, 741, 7-68
DI/DT Limit, 668, 7-49
Drive Fault, 101, 7-18
Droop Filter (Gain), 658, 7-47
Droop Percent, 657, 7-46
Encoder PPR, 609, 7-33
Encoder Velocity, 122, 7-24
End Taper Speed, 666, 7-48