Rockwell Automation 1395 Digital DC Drive FRN 5-10.10/9.30 - Manual (Page 305)

Index
I-11
SP Output 5, 14, 7-15
Stall Delay, 727, 7-64
Start Taper Speed, 665, 7-48
System Inertia, 703, 7-58
System Reset Select, 620, 7-36
Tach Loss CEMF, 731, 7-65
Tach Loss Velocity, 732, 7-65
Tach Switch Ki, 689, 7-55
Tach Switch Kp, 690, 7-55
Tach Switch Select, 691, 7-56
Tach Switch Tolerance, 688, 7-55
Tach Velocity, 156, 7-30
Torque Command, 110, 7-21
Torque Mode, 625, 7-38
Torque Reference 2, 167, 7-32
Torque Reference, 157, 7-30
Trend 1 Contiguous Trigger Switch, 915, 7-76
Trend 1 Enable Trend, 916, 7-77
Trend 1 Operand Parameter X, 910, 7-75
Trend 1 Operand Parameter Y, 911, 7-75
Trend 1 Operator, 912, 7-75
Trend 1 Output Transmit Rate, 917, 7-77
Trend 1 Samples After Trigger Condition is True, 914,
7-76
Trend 1 Sampling Rate, 913, 7-76
Trend Constant Logic Value, 904, 7-73
Trend Constant Logic Value, 905, 7-73
Trend Constant Logic Value, 906, 7-74
Trend Constant Logic Value, 907, 7-74
Trend Constant Signed Value, 900, 7-72
Trend Constant Signed Value, 901, 7-72
Trend Constant Signed Value, 902, 7-73
Trend Constant Signed Value, 903, 7-73
Trend Constant Unsigned Value, 908, 7-74
Trend Constant Unsigned Value, 909, 7-74
Up To Speed Tolerance, 709, 7-60
Velocity Damping Factor, 702, 7-58
Velocity Desired Bandwidth, 700, 7-57
Velocity Error, 124, 7-24
Velocity Feed Forward, 108, 7-21
Velocity Feedback Filter Select, 631, 7-41
Velocity Feedback, 106, 7-20
Velocity Indirect 1, 163, 7-31
Velocity Indirect 2, 164, 7-31
Velocity Indirect 3, 165, 7-31
Velocity Indirect 4, 166, 7-32
Velocity Maximum Bandwidth, 701, 7-57
Velocity Parameter 1 Select, 600, 7-32
Velocity Parameter 2 Select, 601, 7-32
Velocity Parameter 3 Select, 602, 7-32
Velocity Parameter 4 Select, 603, 7-32
Velocity PI Output, 123, 7-24
Velocity Reference Fraction, 153, 7-29
Velocity Reference Whole, 154, 7-29
Warning Select, 632, 7-41
Wn Filter, 693, 7-56
Zero Speed Tolerance, 710, 7-60
Per Unit Numbering, Definition, 7-2
Peripheral Devices
125–300 HP/250–600 HP Drives, 4-13
40–100 HP/75–200 HP Drives, 3-13
Pilot Relay (PR) Control
1–30 HP/2–60 HP Drives, 2-12
125–300 HP/250–600 HP Drives, 4-16
40–100 HP/75–200 HP Drives, 3-17
Port
1–30 HP/2–60 HP Drives, 2-1
125–300 HP/250–600 HP Drives, 4-1
40–100 HP/75–200 HP Drives, 3-1
Definition, 5-1
Position Error, 109, 7-21
Position Feedback, 107, 7-21
Post Samples, 5-22
Setting the Rate, 5-24
Power Board
1–30 HP/2–60 HP Drives, 2-6
1–30 HP/2–60 HP Drives – Illustration, 2-6
Switch and Hardware Location, 1–30 HP/2–60 HP
Drives, 2-7
Power Connections, Standard Field Voltage, 6-15, 6-16,
6-17
Power Distribution
1–30 HP/2–60 HP Drives, 2-11
125–300 HP/250–600 HP Drives, 4-14
40–100 HP/75–200 HP Drives, 3-14
Power Feeder, 6-8
Power Stage Interface
125–300 HP/250–600 HP Drives, 4-8
125–300 HP/250–600 HP Drives – Illustration, 4-9
40–100 HP/75–200 HP Drives, 3-9
40–100 HP/75–200 HP Drives – Illustration, 3-10
Jumper Settings, 6-19
Pre Ramp Velocity Reference, 102, 7-20
Pre-Power Checks, 8-3
Checklist, 8-4
Preset Speed 1, 633, 7-41
Preset Speed 2, 634, 7-42
Preset Speed 3, 635, 7-42
Preset Speed 4, 636, 7-42
Preset Speed 5, 637, 7-42
Preset Speeds, 1-5