Document Outline

• Index
• Chapter1.pdf
  • C H A P T E R 1 Introduction
    • Warnings and FCC Compliance
      • FCC Part 68 Compliance
    • Installation and Configuration
    • Product Warranty
      • New Product Warranty
      • Out-of-Warranty Product Repairs
      • Troubleshooting Fee
      • Shipping
• Chapter2.pdf
  • C H A P T E R 2 System Overview
    • ADS FlowShark Flow Monitor
      • Available FlowShark Monitors
      • Communications
      • Digital Signal Processor
      • Digital Signal Processor with Communication
      • Analog Board
      • Communications Board
      • Voltage Regulator Board
      • Analog 4-20mA I/O Board
      • Connectors
      • Power
        • Internal Power
        • External Power
    • Sensors
      • Ultrasonic Depth Sensor
        • Quadredundancy
        • Ultrasonic Depth Processing
        • Data Scrubbing
      • Pressure Depth Sensor
      • Doppler Velocity Sensor
    • Inputs/Outputs
      • Digital I/O
      • Analog 4-20mA I/O
      • Modbus
• Chapter4.pdf
  • C H A P T E R 4 Communication
    • Providing Telephone Service
      • Running the Telephone Cable Between the Monitor and Service Locations
      • Mounting the Lightning Protection Module
      • Preparing the Telephone Cable
      • Wiring the Telephone Cable to the Monitor
      • Wiring the Telephone Cable to the Lightning Protection Module
      • Wiring the Lightning Protection Module to the Network Interface Box
    • Setting Up Wireless Communication
      • Installing the Antenna
        • Installing a Wireless Antenna in the Road
        • Installing a Wireless Antenna in a Telephone Pedestal Off the Road
        • Mounting a Wireless Antenna to an Enclosure, Conduit, or Antenna Mast
        • Mounting a Wireless Antenna on a Roof or Other Protected Structure
    • Connecting to the Monitor in the Field
• Chapter9.pdf
  • C H A P T E R 9 Modbus
    • Configuring the FlowShark Monitor to Operate in Real-Time
    • Defining the Modbus Register Values
      • Modbus Data Type
    • Connecting the FlowShark to Modbus
      • RS232 Port Settings
    • Verifying Modbus Output Values
• Chapter10.pdf
  • C H A P T E R 10 Maintenance and Troubleshooting
    • Maintaining the System Components
      • Gathering Replacement Parts and Supplies
      • Inspecting the Monitor
        • Confirming the Monitor
        • Replacing the Monitor Battery Packs
      • Checking the Sensors
        • Replacing the Pressure Depth Sensor Dryer Tube or Desiccant
          • Replacing the Dryer Tube
          • Replacing the Desiccant
      • Checking Communication Devices
    • Troubleshooting
      • General Monitor Problems
      • External Power
      • Ultrasonic Depth Subsystem
      • Doppler Velocity Subsystem
      • Pressure Depth Subsystem
• AppendixB.pdf
  • A P P E N D I X B FlowShark Models and Capabilities
• AppendixC.pdf
  • A P P E N D I X C Modbus Output Registry Entities and Values
• Chapter7.pdf
  • C H A P T E R 7 Monitor Installation
    • Mounting the Monitor to the Manhole Wall
    • Mounting the Monitor to the Manhole Rim
• FlowSharkMasterA4.pdf
  • Table of Contents
• AppendixA.pdf
  • A P P E N D I X A Specifications
    • ADS FlowShark Flow Monitor
    • Boards
      • Digital Signal Processor Board (5000-0514)
      • Digital Signal Processor Board with Communications (5000-0514-01)
      • Analog Board (5000-0515)
      • Communication Board (5000-0516)
      • GPRS Wireless Modem Board (5000-0761)
      • Land-line Modem Board (5000-0570)
      • Analog 4-20mA I/O Board (5000-0517)
      • Voltage Regulator Board (5000-0518)
    • ADS Power Supply (5000-0727)
    • Sensors
      • Ultrasonic Depth Sensor (103262A-30)
      • Pressure Depth Sensor (3704-0041/42/16-35/40)
      • Doppler Velocity Sensor (103260A-35)
    • Lightning Protection Module (103313)
    • Antennas (for Wireless Communication)
• Chapter8.pdf
  • C H A P T E R 8 Analog Input/Output Installation and Configuration
    • Analog Inputs
      • Gathering Tools and Equipment
      • Connecting Analog Inputs
      • Verifying the Analog Input Values
    • Analog Outputs
      • Loop Power
      • Signal Connection
      • Typical Analog Output Installation
• Chapter5.pdf
  • C H A P T E R 5 External Power
    • Typical Installation
      • DC Power Requirements
      • Installation of the ADS Power Supply
      • Installation of the External Power Cable
      • Upgrade Kit to Convert from Battery Power to External Power
• Chapter3.pdf
  • C H A P T E R 3 Sensor Installation and Connection
    • Investigating Site Characteristics
      • Flow Hydraulics
      • Pipe and Manhole Characteristics
    • Installing the Sensors in the Pipe
      • Standard Installation
        • Gathering Parts and Supplies
        • Gathering Tools and Equipment
        • Assembling the Ring
        • Mounting the Sensors to the Ring
          • Mounting the Ultrasonic Depth Sensor
          • Mounting the Doppler Velocity Sensor
          • Mounting the Pressure Depth Sensor
        • Securing the Cables to the Ring
        • Installing the Ring in the Pipe
      • Special Installations
        • Gathering Parts and Supplies
        • Gathering the Tools and Equipment
        • Mounting the Ultrasonic Depth Sensor
          • Standard Ultrasonic Mount
          • Surcharge Mount
        • Mounting the Doppler Velocity and Pressure Depth Sensors
          • ¾-Band Mount
          • ½-Band Mount
        • Securing the Cables to the Band
    • Securing the Sensor Cables in the Pipe and Manhole
    • Connecting Sensors to the Monitor
      • Securing the Dryer Tube to the Monitor
• AppendixD.pdf
  • A P P E N D I X D Part Numbers
• Chapter6.pdf
  • C H A P T E R 6 Configuration and Activation
    • Configuring the Monitor Location
      • Launching the Profile Software
      • Creating a Monitor Location
      • Creating an Installation Table
      • Selecting and Editing Devices
        • Editing the Ultrasonic Device
        • Editing the Velocity Device
        • Editing the Pressure Device
        • Editing the MLI Device
    • Setting the Communication Parameters
    • Activating the Monitor
    • Running Device Diagnostics
    • Collecting Data from the Monitor
    • Upgrading the Monitor Firmware
    • Viewing Diagnostic and Data Logs