Calibration menu, Ports com menu – Rice Lake 880 Performance Series Indicator/Controller Technical/Service Manual User Manual
Page 74
68
880 Technical/Service Manual
Calibration Menu
Table 6-5. CALIBR EDP Commands
Command
Menu
Description
Choices / Range
SC.WZERO#1
WZERO
Perform zero calibration
n/a
SC.WSPAN#1
WSPAN
Perform span calibration
n/a
SC.LC.CD#1
n/a
Raw count at zero
-2147483646 to 2147483647
SC.LC.CW#1
n/a
Raw count at span
-2147483646 to 2147483647
SC.LC.CZ#1
n/a
-2147483646 to 2147483647
SC.REZERO#1
REZERO
Perform zero caibration
n/a
SC.WLIN.C1#1
n/a
Calibrate linearization point 1
n/a
SC.WLIN.C2#1
n/a
Calibrate linearization point 2
n/a
SC.WLIN.C3#1
n/a
Calibrate linearization point 3
n/a
SC.WLIN.C4#1
n/a
Calibrate linearization point 4
n/a
SC.WLIN.C5#1
n/a
Calibrate linearization point 5
n/a
SC.WLIN.F1#1
CAL 1
Raw count value for linearization point 1
-2147483646 to 2147483647
SC.WLIN.F2#1
CAL 2
Raw count value for linearization point 2
-2147483646 to 2147483647
SC.WLIN.F3#1
CAL 3
Raw count value for linearization point 3
-2147483646 to 2147483647
SC.WLIN.F4#1
CAL 4
Raw count value for linearization point 4
-2147483646 to 2147483647
SC.WLIN.F5#1
CAL 5
Raw count value for linearization point 5
-2147483646 to 2147483647
SC.WLIN.V1#1
WGT 1
Test weight value for linearization point 1
0.0 - 999999.0
SC.WLIN.V2#1
WGT 2
Test weight value for linearization point 2
0.0 - 999999.0
SC.WLIN.V3#1
WGT 3
Test weight value for linearization point 3
0.0 - 999999.0
SC.WLIN.V4#1
WGT 4
Test weight value for linearization point 4
0.0 - 999999.0
SC.WLIN.V5#1
WGT 5
Test weight value for linearization point 5
0.0 - 999999.0
SC.WVAL#1
WVAL
Test weight value
0.00001 - 999999.0
Note
The menu items, CAL1 – CAL5 are used to do the calibration. A value cannot be keyed in.
The SC.WLIN.Fx#1 EDP commands can be used to view and edit the value but they do not perform the
calibration. Use the SC.WLIN.Cx#1 commands to perform the calibration.
Ports COM Menu
Table 6-6. PORTS (COM) EDP Commands
Command
Menu
Description
Choices / Range
EDP.BAUD#1
BAUD
Port baud rate
1200, 2400, 4800, 9600, 19200,
28800, 38400, 57600, 115200
EDP.BITS#1
BITS
Port data bits and parity
8NONE, 7EVEN, 7ODD
EDP.ECHO#1
ECHO
Specifies whether characters received by the
port are echoed back to the sending unit
OFF, ON
EDP.EOLDLY#1
EOLDLY
Port end-of-line delay in 0.1 sec intervals
Range: 0 - 255
EDP.TYPE#1
TYPE
Specifies RS-232 or RS-485 communication
232, 485
EDP.ADDRESS#1
ADDRES
RS-485 address
Range: 0 - 255
EDP.PRNMSG#1
PRNMSG
Print message
OFF, ON
EDP.RESPONSE#1
RESPNS
Response
OFF, ON
EDP.SFMT#1
SFMT
Stream format
Alphanumeric, max Length: 200
EDP.STOPBITS#1
STOP B
Stop Bits
1, 2
EDP.TERMIN#1
TERMIN
Termination character
CR/LF, CR
EDP.TRIGGER#1
TRIGGE
Selects the operation of the port
COMAND, STRLFT, STRIND,
REMOTE