IDEC MicroSmart Pentra User Manual
Page 157
A
PPENDIX
9-10
FC5A MicroSmart PID Module User’s Manual FC9Y-B1283
Blocks 4, 5 Initial Setting Parameters
Offset from
the Control
Register
Parameter
Default Value
CH0
CH1
+53
+130 Control Action
0: Reverse action (Heating)
+54
+131 Heating/Cooling Control (CH0 only)
[CH0] 0: Disable
[CH1] 0
+55
+132 External SP Input (CH0 only)
[CH0] 0: Disable
[CH1] 0
+56
+133 Input Function
[CH0/CH1] 0: Input (CH0/CH1)
+57
–
Output Function (CH0)
[CH0] 0: Output (CH0)
–
+134 Output Function (CH1)
[CH1] 0: Output (CH1)
+58
+135 Input Type
00h: Type K thermocouple -200 to 1370°C
+59
+136
Set Point (SP) Upper Limit/Linear Conversion
Maximum Value
1370°C (1370)
+60
+137
Set Point (SP) Lower Limit/Linear Conversion
Minimum Value
-200°C (-200)
+61
+138 Output ON/OFF Hysteresis
1.0°C (10)
+62
+139
PV Correction
0.0°C (0)
+63
+140
PV Filter Time Constant
0.0 seconds (0)
+64
+141
Reserved
0
+65
+142
Alarm 1 Type
0: No alarm action
+66
+143
Alarm 2 Type
+67
+144
Alarm 3 Type
+68
+145
Alarm 4 Type
+69
+146
Alarm 5 Type
+70
+147
Alarm 6 Type
+71
+148
Alarm 7 Type
+72
+149
Alarm 8 Type
+73
+150
Alarm 1 Hysteresis
1.0°C (10)
+74
+151
Alarm 2 Hysteresis
+75
+152
Alarm 3 Hysteresis
+76
+153
Alarm 4 Hysteresis
+77
+154
Alarm 5 Hysteresis
+78
+155
Alarm 6 Hysteresis
+79
+156
Alarm 7 Hysteresis
+80
+157
Alarm 8 Hysteresis
+81
+158
Alarm 1 Delay Time
0.0 seconds (0)
+82
+159
Alarm 2 Delay Time
+83
+160
Alarm 3 Delay Time
+84
+161
Alarm 4 Delay Time
+85
+162
Alarm 5 Delay Time
+86
+163
Alarm 6 Delay Time
+87
+164
Alarm 7 Delay Time
+88
+165
Alarm 8 Delay Time
+89
+166
AT Bias
20°C (20)
+90
+167
Control Mode
0: Fixed value control
+91
+168
Program Control Mode Start Type
0: PV start
+92
+169
Step Time Unit
0: Minute
+93
+170
Program End Action
0: Terminate program control
+94
+171
Proportional Term
0: Proportional band
+95
+172
Cooling Method (CH0 only)
[CH0] 0: Air cooling
[CH1] 0
+96
+173
Set Point (SP) when Program Control Starts 0.0°C (0)
+97
+174
Number of Repeats
0 times (0)
+98
+175
Cooling Output ON/OFF Hysteresis
(CH0 only)
[CH0] 1.0°C (10)
[CH1] 0
+99
+176
Output Specifications
(FC5A-F2M2 only)
0: Non-contact voltage output (for SSR
drive)
+100 +177
External SP Input Bias
(CH1 only)
[CH0] 0
[CH1] 0.0°C (0)
+101 +178
External SP Input Linear Conversion
Maximum Value (CH1 only)
[CH0] 0
[CH1] 1370°C (1370)
+102 +179
External SP Input Linear Conversion
Minimum Value (CH1 only)
[CH0] 0
[CH1] -200°C (-200)