IDEC MicroSmart Pentra - Manual (Page 61)

D EVICE A LLOCATION OF PID M ODULE
5-20 FC5A MicroS mart PID Module User’s Manual FC9Y-B1283
+73 +150 Alarm 1 Hysteresis
When input range unit is Celsius:
0.1 to 100.0°C
When input range unit is Fahrenheit:
0.1 to 100.0°F
When input is voltage or current input:
1 to 1000
R/W
+74 +151 Alarm 2 Hysteresis R/W
+75 +152 Alarm 3 Hysteresis R/W
+76 +153 Alarm 4 Hysteresis R/W
+77 +154 Alarm 5 Hysteresis R/W
+78 +155 Alarm 6 Hysteresis R/W
+79 +156 Alarm 7 Hysteresis R/W
+80 +157 Alarm 8 Hysteresis R/W
+81 +158 Alarm 1 Delay Time
0 to 10000 sec
R/W
+82 +159 Alarm 2 Delay Time R/W
+83 +160 Alarm 3 Delay Time R/W
+84 +161 Alarm 4 Delay Time R/W
+85 +162 Alarm 5 Delay Time R/W
+86 +163 Alarm 6 Delay Time R/W
+87 +164 Alarm 7 Delay Time R/W
+88 +165 Alarm 8 Delay Time R/W
+89 +166 AT Bias
When input range unit is Celsius:
0 to 50 °C (0.0 to 50.0°C for input with decimal point)
When input range unit is Fahrenheit:
0 to 100 °F (0.0 to 100.0°F for input with decimal point)
R/W
+90 +167 Control Mode
0: Fixed value control mode
1: Program control mode
R/W
+91 +168
Program Control Mode Start
Type
0: PV start
1: PVR start
2: SP start
R/W
+92 +169 Step Time Unit
0: Minute
1: Second
R/W
+93 +170 Program End Action
0: Terminate program control
1: Continue program control (Repeat)
2: Hold program control
R/W
+94 +171 Proportional Term
0: Proportional band
1: Proportional gain
R/W
+95 +172
Cooling Method
(CH0 only)
0: Air cooling
1: Oil cooling
2: Water cooling
R/W
+96 +173
Set Point (SP) when Program
Control Starts
When input is thermocouple or resistance thermometer:
Set point (SP) lower limit to set point (SP) upper limit
When input is voltage or current input:
Linear conversion min. to linear conversion max.
R/W
+97 +174 Number of Repeats 0 to 10000 times R/W
+98 +175
Cooling Output ON/OFF
Hysteresis
(CH0 only)
When input range unit is Celsius:
0.1 to 100.0°C
When input range unit is Fahrenheit:
0.1 to 100.0°F
When input is voltage or current input:
1 to 1000
R/W
+99 +176
Output Type
(FC5A-F2M2 only) 0: Non-contact voltage output (for SSR drive)
1: Current output
R/W
+100 +177
External SP Input Bias
(CH1 only)
±20% of the external SP input linear conversion span R/W
+101 +178
External SP Input Linear
Conversion Maximum Value
(CH1 only)
External SP input Linear conversion min. to input range
upper limit
R/W
+102 +179
External SP Input Linear
Conversion Minimum Value
(CH1 only)
Input range lower limit to external SP input linear conversion
max.
R/W