Document Outline

• PREFACE
• 1. Introduction And General Description
  • 1-1. Instrument check
  • 1-2. Application
• 2. GENERAL SPECIFICATIONS
  • 2-1. Specifications
  • 2-2. Model and suffix codes
  • 2-3. Control Drawing ISC202S mA HART® Specification (IECEx).
  • 2-4. Control Drawing ISC202S mA HART® Specification (ATEX)
  • 2-5. Control Drawing ISC202S mA HART® Specification (FM Intrinsically safe design)
  • 2-6. Control Drawing ISC202S mA HART® Specification (FM Non-incendive design)
  • 2-7. Control Drawing of ISC202S mA HART® Specification (CSA)
  • 2-8. Control Drawing of ISC202S FF/PB Specification (IECEx)
  • 2-9. Control Drawing of ISC202S FF/PB Specification (ATEX)
  • 2-10. Control Drawing of ISC202S FF/PB Specification (FM Intrinsically safe Entity)
  • 2-11. Control Drawing of ISC202S FF/PB Specification (FM Intrinsically safe FISCO)
  • 2-12. Control Drawing of ISC202S FF/PB Specification (FM Non-incendive Entity)
  • 2-13. Control Drawing of ISC202S FF/PB Specification (FM Non-incendive FNICO)
  • 2-14. Control Drawing of ISC202S FF/PB Specification (CSA)
• 3. Installation And Wiring
  • 3-1. Installation and dimensions
    • 3-1-1. Installation site
    • 3-1-2. Mounting methods
  • 3-2. Preparation
    • 3-2-1. Cables, terminals and glands
  • 3-3. Wiring of sensors
    • 3-3-1. General precautions
    • 3-3-2. Additional precautions for installations in hazardous areas
    • 3-3-3. Installation in: Hazardous Area-Non-Incendive
  • 3-4 Wiring of the power supply
    • 3-4-1 General precautions
    • 3-4-2. Connection of the power supply
    • 3-4-3. Switching the instrument on
  • 3-5. Sensor wiring
  • 3-6. Other sensor systems
    • 3-6-1. Sensor cable connections using junction box (BA10) and extension cable (WF10)
• 4. Operation; Display Functions And Setting
  • 4-1. Operator interface
  • 4-2. Explanation of operating keys
  • 4-3. Setting passcodes
    • 4-3-1. Passcode protection
  • 4-4. Display examples
  • 4-5. Display functions
• 5. Parameter setting
  • 5-1. Maintenance mode
    • 5-1-1. Introduction
    • 5-1-2. Manual calibration to determine the cell constant (C.C.)
    • 5-1-3. Second Line display. Referring to the first compensated conductivity.
    • 5-1-4. Second Line display. Referring to the second compensated conductivity.
    • 5-1-5. Manual activation of HOLD
  • 5-2. Commissioning mode
    • 5-2-1. Linear output (Range)
    • 5-2-2. HOLD
    • 5-2-3. Temperature compensation
    • 5-2-4. Temperature compensation for first conductivity value
    • 5-2-5. Temperature Compensation for second conductivity value
  • 5-3. Service Codes
    • 5-3-1. Parameter specific functions
    • 5-3-2. Temperature measuring functions
    • 5-3-3. Temperature compensation functions
    • 5-3-4. mA output functions
    • 5-3-5. User interface
    • 5-3-6. Communication setup
    • 5-3-7. General
• 6. Calibration
  • 6-1 When is calibration necessary?
  • 6-2. Calibration procedure
• 7. Maintenance
  • 7-1. Periodic maintenance for the EXA 202 transmitter
  • 7-2. Periodic maintenance of the sensor
• 8. Troubleshooting
  • 8-1. Introduction
  • 8-2. Self diagnostics of the conductivity sensor
  • 8-3. Self diagnostics of the temperature sensor
  • 8-4. Self diagnostics of the electronics
  • 8-5. Checking during operation
• 9. Error messages and explanation
• 10. Spare Parts
• 11. Appendix 1
  • 11-1. User setting for non-linear output table (code 31, 35)
  • 11-2. User entered matrix data (code 23 to 28)
  • 11-3. Matrix data table (user selectable in code 22)
  • 11-4. Configuration Checklist For ISC202
  • 11-5. Coded service settings (default)
  • 11-6. Device Description (DD) menu structure
• 12. APPENDIX 2
  • 12-1. Preface
  • 12-2. Wiring diagrams
  • 12-3. Peripheral products
    • 12-3-1. PH201G*B Dedicated Distributor
    • 12-3-2. BA20 Junction Terminal Box
    • 12-3-3. WF10J Extension Cable
  • 12-4. Quick reference for parameter setting
    • 12-4-1. Settings Performed in Maintenance Mode
      • 12-4-1-1 Calibration with solution of known conductivity
        • 12-4-1-2 Selecting Items for Display
    • 12-4-2. Commissioning Mode Settings
      • 12-4-2-1 Output Range Setting
      • 12-4-2-2 Setting Hold Functions
      • 12-4-2-3 Temperature Compensation
      • 12-4-2-4 Correcting Zero Offset Error by Calibration in Air (Air Set)
    • 12-4-3. Actual Setting Examples
      • 12-4-3-1 Setting Output in terms of Concentration
      • 12-4-3-2 Key Operation Procedure Examples
  • 12-5. Installation factor adjustment
• 13. Appendix 3 QUALITY INSPECTION
  • 13-1. ISC202G 2-Wire Inductive Conductivity Transmitter
  • 13-2. ISC202S 2-Wire Inductive Conductivity Transmitter
  • 13-3. ISC202G, ISC202S 2-Wire Inductive Conductivity Transmitter (Fieldbus Communication)
  • 13-4. ISC202G, ISC202S 2-Wire Inductive Conductivity Transmitter (Profibus Communication)
• CMPL
• Revision Record
• Supplement