Yokogawa Standalone MW100 - Manual (Page 24)

1-17 IM MW100-17E
Commands
1
2
3
App App
Index
When Setting Scaling
Setting SRp1,p2,p3,p4,p5,p6,p7,p8,p9,p10
<terminator>
p1 Channel range (001 to 060)
p2 Input type
VOLT
DC voltage
TC Thermocouple
RTD Resistance temperature
detector
DI Contact input
OHM Resistance input
STR Strain input
PULSE Pulse
p3 Measuring range
p4 Lower limit of span
p5 Upper limit of span
p6 MATH type (SCALE)
p7 Scaling lower limit (-30000 to 30000)
p8 Scaling upper limit (-30000 to 30000)
p9 Decimal place (0 to 4)
p10 Unit (max 6 characters)
Query SR[p1]?
Example Convert the DC voltage measured on channel 2 to
DC current. Set the measuring range to 6V (high
resolution), lower limit of span to 1 V, upper limit of span
to 5 V, lower limit of scaling to 0.00A, and upper limit of
scaling to 5.00A.
SR002,VOLT,6VH,10000,50000,SCALE,0,500,
2,A
Explanation • Set the p3, p4, and p5 setting parameters according
to the table in section 1.3.
• Specify measurement channels on p1.
• For the characters that can be used for p10, see
user specified characters in section 1.3.
SF Filter Settings
Setting SFp1,p2<terminator>
p1 Channel range (001 to 060)
p2 Filter coefficient (0, 5, 10, 20, 25,
40, 50, 100)
Query SF[p1]?
Example Set the filter coefficient for channel 2 to 5.
SF002,5
Explanation Specify measurement channels on p1. However, do not
set this on the channels of the digital input module.
XB Burnout Settings
Setting XBp1,p2<terminator>
p1 Channel range (001 to 060)
p2 Burnout processing (OFF, UP, DOWN)
Query XB[p1]?
Example Set UP (+OVER) when burnout occurs on channel 1.
XB001,UP
Explanation Specify measurement channels that can accept TC
input for p1.
XJ Reference Junction
Compensation Settings
Setting When p2=INT
XJp1,p2<terminator>
When p2=EXT
XJp1,p2,p3<terminator>
For an Internal Compensation Circuit
Setting XJp1,p2<terminator>
p1 Channel range (001 to 060)
p2 Reference junction compensation
selection (INT)
Query XJ[p1]?
Example Set RJC on channel 1 to internal
compensation circuit.
XJ001,INT
Explanation Specify measurement channels that can accept TC
input for p1
For External RJC
Setting XJp1,p2,p3<terminator>
p1 Channel range (001 to 060)
p2 Reference junction compensation
selection (EXT)
p3 External RJC value (-20000 to 20000)
Query XJ[p1]?
Example Set RJC on channel 2 to external RJC, and the
compensation value to 0 µV.
XJ002,EXT,0
Explanation • Units of p3 are µV.
• Specify measurement channels that can accept TC
input for p1.
PF Pulse Input Module Chattering
Filter Settings
Setting PFp1,p2
p1 Channel range (001 to 060)
p2 Chattering filtering (OFF/ON)
Query PF[p1]?
Example Turn on the chattering filter on channel 23.
PF23,ON
Explanation For p1, specify channels included on the pulse input
module.
1.4 Setting Commands (System Related)