Rockwell Automation 900 Temperature Controller Communications Functions - Series B - Manual (Page 52)

Publication 900-UM004D-EN-E - July 2010
3-10 Communications Data
C3 (83) 004E Control output 1
assignment When control output 1 is a linear output:
H’00000000 (0): Not assigned.
H’00000001 (1): Control output (heating)
H’00000002 (2): Control output (cooling)
When control output 1 is an ON/OFF pulse output:
H’00000000 (0): Not assigned.
H’00000001 (1): Control output (heating)
H’00000002 (2): Control output (cooling)
H’00000003 (3): Alarm 1
H’00000004 (4): Alarm 2
H’00000005 (5): Alarm 3
H’00000006 (6): Program end output➒
H’00000007 (7): Control output ON/OFF count alarm ➓ Advanced
function
setting
C3 (83) 004F Control output 2
assignment H’00000000 (0): Not assigned.
H’00000001 (1): Control output (heating)
H’00000002 (2): Control output (cooling)
H’00000003 (3): Alarm 1
H’00000004 (4): Alarm 2
H’00000005 (5): Alarm 3
H’00000006 (6): Program end output➒)
H’00000007 (7): Control output ON/OFF count alarm ➓
C3 (83) 0050 Auxiliary Output 1
assignment H’00000000 (0): Not assigned.
H’00000001 (1): Control output (heating)
H’00000002 (2): Control output (cooling)
H’00000003 (3): Alarm 1
H’00000004 (4): Alarm 2
H’00000005 (5): Alarm 3
H’00000006 (6): Program end output➒)
H’00000007 (7): Control output ON/OFF count alarm ➓
C3 (83) 0051 Auxiliary Output 2
assignment H’00000000…H’0000000F (0…15)
* Same settings as Auxiliary Output 1 assignments
C3 (83) 0052 Character select H’00000000 (0): OFF
H’00000001 (1): ON
C3 (83) 0053 Program pattern H’00000000 (0): OFF
H’00000001 (1): STOP
H’00000002 (2): CONT Initial
setting
Table 3.3 Variable Type C3 (83)
Variable
Type Address Item (Parameter) Set (Monitor) Value Function
Group
➊ The input type can be selected to march the connected sensor. There are two input types specifications:
Thermocouple/Resistance thermometer input and Analog input.
➋ The parameter will not be shown on the Controller display when alarm 3 is not assigned to an output.
➌ Communications parameters are enabled after they have been changed by resetting the controller.
➍ For controllers with two event inputs (events 1 and 2), this cannot be set if the number of Multi-SP uses parameter is set to 1
or 2
➎ For controllers with two event inputs (events 1 and 2), this cannot be set if the number of Multi-SP uses parameter is set to 2.
➏ PRST (program start) can be set even when the program pattern is set to OFF, but the function will be disabled.
➐ The logic of CompoWay/F (900-TC) operation command code 00 (communications writing) is not affected.
➑ The setting (monitor) range depends on the transfer output type setting. (See the setting data list for details.)
➒ P.END (program end output) can be set even when the program pattern is set to OFF, but the
function will be disabled.
➓ The output turns ON when the status of either the Control Output 1 ON/OFF Count Alarm or the Control Output 2 ON/OFF
Count Alarm turns ON.