Document Outline

• CENTERLINE 2500 Low Voltage Motor Control Centers
• Important User Information
• Summary of Changes
  • New and Updated Information
• Table of Contents
• Preface
  • Additional Resources
  • Purchased Components and Additional Instruction Sheets
• 1 - System Overview
  • ArcShield Rating
  • IntelliCENTER Software
    • IntelliCENTER Features
    • IntelliCENTER Software
  • Structure
    • Dimensions
  • Typical Column Construction
  • Technical Data
  • Nameplate Data
  • Motor Control Center Sequence Numbering
  • ArcShield Labels
• 2 - Receiving, Handling, and Storage
  • Receiving
  • Handling
  • Storage
• 3 - Install Columns
  • Location Planning
    • ArcShield Clearance Space
    • Environment
  • Remove Packing Materials
    • Locating Bus Splice Kits
    • Removing the Covers
    • Positioning the Motor Control Center
  • Securing a Motor Control Center
    • Securing Methods
    • Sealing IP54 Enclosures Before Securing
    • Securing Single-front, One-column-wide Shipping Blocks
    • Securing Single-front, Two-column-wide Shipping Blocks
    • Securing Double-front, One-column-wide Shipping Blocks
    • Securing Multiple-column Shipping Blocks
    • Joining Columns
  • Seismic Capabilities
  • Splicing the Power Bus
    • Accessing the Power Bus
    • Splicing Power Bus, 800…4000 A
    • Splicing the Protective Earth (PE) Conductor
    • Control and Network Cables
  • Torque Specifications
• 4 - Install Cable
  • Install ArcShield Protection After Wiring
  • Lugs
  • Incoming Line Lug Compartment
  • Main Disconnecting Means
  • Cable Bracing
  • Secure Load Wires
• 5 - Door Latches, Operator Handles, and Unit Interlocks
  • Height Considerations
  • Door Latches
    • Quarter-turn Door Latches
    • ArcShield Door Latches
  • Small Rotary-operator Handles
    • Opening the Unit Door
    • Closing the Unit Door
    • Opening the Unit Door in the ON/I Position
    • Operator Handles for Circuit Breakers
    • Locking Units in the OFF/O Position
    • Locking Units in the ON/I Position
  • Large Rotary-operator Handles
    • Opening the Unit Door
    • Closing the Unit Door
    • Opening the Unit Door in the ON/I Position
    • Operator Handles for Circuit Breakers
    • Locking Units in the OFF/O Position
    • Locking Units in the ON/I Position
  • Unit Interlocks
• 6 - Install and Remove Units
  • Unit Size
  • Withdrawable Units
    • Operating Positions
    • Selecting an Operating Position
  • Safety Guidelines for Installing and Removing Withdrawable Units
  • Inserting a Withdrawable Unit
  • Removing a Withdrawable Unit
  • Removing the Unit Door
    • Multiple Module Unit Doors
    • One Module Unit Doors
• 7 - Commissioning
  • Introduction
  • Pre-commissioning Checklist
  • Commissioning Procedure
• 8 - Maintenance
  • Establish a Maintenance Program
  • Suggested Maintenance Guidelines
• 9 - IntelliCENTER Options
  • EtherNet/IP Motor Control Centers
    • Connection Count
    • Cable Length Limitations
    • Cable Routing
    • Adding a MCC Unit to an EtherNet/IP System
    • Ethernet Power Supply
    • Connecting Power Supplies–Remote or in the MCC Lineup
    • Network Power Supply and the Protective Earth Circuit
    • Connecting Two Power Supplies
    • System Design Installation Checklist
    • EtherNet/IP Software Installation Checklist
  • DeviceNet Motor Control Centers
    • Preparing a DeviceNet System for Commission
    • Terminating Resistors
    • Joining DeviceNet Cables
    • DeviceNet Power Supply
    • Connecting Power Supplies–Remote or in the MCC Line-Up
    • Network Power Supply and the Protective Earth Circuit
    • Connecting Two Power Supplies
  • Electronic Data Sheets (EDS)
    • Overview
    • Where to Find EDS Files
    • Installing EDS Files
    • Finding EDS Files for Other Devices
    • Uploading EDS Files from the Device
• A - Worksheets
  • Sample MCC Layout Worksheet
• Glossary
• Index
• Untitled
• Back Page/Rockwell Support