KEYENCE LT-9001 Series - Manual (Page 127)

7-13
E LT-9001-IM
7
Chapter
I/O
Terminal
Sampling cycle (T2), minimum input time (internal processing time, binary strobe cycle) (T1)
Timing Details (LT-9010 (M))
[ms]
Minimum input time
Scan width/
Sampling cycle (T2) Internal processing time (T1)
interval
OUT STB/BIN STB cycle
Displacement
Profile mode
Displacement
Profile mode
mode FINE=OFF FINE=ON mode FINE=OFF FINE=ON
OFF 0.64
120/2 42.3 42.3 164 2.6
120/5 26.9 26.9 96 3.2
120/10 19.2 19.2 64 3.2
250/2 84.5 84.5 323 2.6
250/5 43.6 43.6 173 3.2
250/10 28.2 28.2 96 3.2
500/2 164 164 646 2.6
500/5 75.6 75.6 327 3.2
500/10 43.6 43.6 167 3.2
1100/2 356 356 1420 2.6
1100/5 153 153 711 3.2
1100/10 82 82 359 3.2
4/1 2.6
* The sampling cycle(T2) differs according to the manufacturing variations of individual measuring units.
* The sampling cycle(T2) differs according to the settings of "Scan width/interval".
* The measurement response time, average measurement time, update cycle (T5), and RESET time (T4) vary according to the
change in the sampling cycle (T2).
* The minimum input time (internal processing time, binary strobe cycle) (T1) varies according to the setting of FINE mode.
Average measurement time, RESET time (T4), update cycle (T5)
Number of Average
Displacement mode Profile mode
measurement times measurement Number of data for RESET time Update cycle Number of data for RESET time Update cycle
for averaging time moving average (T4) (T5) moving average (T4) (T5)
2 T2x2 1 T2x3 T2x1 2 T2x5 T2x2
4 T2x4 1 T2x5 T2x1 2 T2x7 T2x2
8 T2x8 1 T2x9 T2x1 2 T2x11 T2x2
16 T2x16 1 T2x17 T2x1 2 T2x19 T2x2
32 T2x32 1 T2x33 T2x1 2 T2x35 T2x2
64 T2x64 1 T2x65 T2x1 2 T2x67 T2x2
128 T2x128 2 T2x129 T2x2 4 T2x131 T2x4
256 T2x256 4 T2x257 T2x4
512 T2x512 8 T2x513 T2x8
1024 T2x1024 16 T2x1025 T2x16
2048 T2x2048 32 T2x2049 T2x32
4096 T2x4096 64 T2x4097 T2x64
* T2 is a sampling cycle.
* Number of times for averaging raging from 256 to 4096 can only be selected when the scanning width/interval is set to OFF in the
displacement mode. Refer to "SCAN" (page 3-15) for details.
* Average measurement time does not mean measurement response time. Refer to "Measurement Response Time" (page 9-6)
* The moving average is used for the measured value averaging function. Refer to "OUT (Output)" (page 5-8) for details.
0.64 0.64