KEYENCE LT-9001 Series - Manual (Page 167)

B
Basic operations that stabilize measurement ....2-20
BASIC settings ...............................2-6, 3-15, 4-13
Baud rate [BAUDRATE] ....6-2, 6-5, 8-2, 8-3, 8-17
[BEEP] ..............................................................6-3
Beep sound .......................................6-2, 6-3, 6-7
BIN OUT output ................................................7-7
BIN SEL input ...................................................7-7
BINARY ...................................................5-20, 7-7
Binary output ..........................7-4, 7-7, 7-10, 7-11
Binary output content selection input...............7-4
Binary output content selection output ............7-4
Bottom hold [BOTTOM] ............................5-9, 7-9
C
CA-MN80 .........................................................A-5
CA-MN80 dedicated mount .............................A-5
Calibration ...............................................5-16, 8-8
Calibration setting ..........................................8-11
CALIB (Calibration) ........................................5-16
CAMERA IMAGE ............................................5-18
CENT FIX (Center fix) .....................................5-18
Change parameter command format...............8-8
Changing the light intensity level ...................2-20
Changing the scan width and the FINE
mode ..............................................................2-20
Check parameter command format ...............8-15
Connecting cable .............................................1-5
Connection .......................................................1-8
Connector terminals (Control I/O) ....................1-4
Coefficient .................................................6-3, 6-7
CONSOLE .................................................6-2, 6-6
Control I/O ...............................................5-20, 7-3
Controller ..........................................................1-4
Controller Error.................................................A-4
Correcting measurement errors due
to angled targets ...................................3-19, 4-18
[CR] ..................................................................8-3
D
D-LENGTH ................................6-2, 6-5, 8-3, 8-17
D-MODE ...................................6-2, 6-5, 8-3, 8-17
DARK .............................................3-17, 4-16, 7-7
Dark setting display bar ............................3-4, 4-4
Dark-out............................................................8-8
[DARK OUT] ...................................................4-16
Symbol
+1P, +2P, +3P, +4P .......................................3-13
-1P, -2P, -3P, -4P ............................................3-13
3-step judgment output ....................................7-5
8.4" color LCD monitor .....................................A-5
∆Slant .............................................................3-10
∠Correct (THICK mode only).........................3-19
A
AC power inlet ..................................................1-5
Adjusting the distance between the measuring
unit and the measurement target ..........2-14, 2-17
Analog monitor output ......................................7-3
ANALOG output .............................................5-15
Analog scaling ...............................5-15, 8-8, 8-11
Analog voltage output .............................7-8, 7-11
Area...........................................................4-9, 8-8
AREA ..............................................................4-13
Area 1 ..............................................4-3, 4-9, 4-13
Area 2 ..............................................4-3, 4-9, 4-13
Area range .......................................................8-8
Area range setting..........................................8-11
Area setting ....................................................8-11
Area setting for the area measurement..........4-13
Area settings display ................................4-3, 4-4
Area settings display bar ..........................4-3, 4-4
ASCII ................................................................8-2
ASCII code table ............................................8-16
Auto bottom hold [A.BOTTOM] .................5-9, 7-9
Auto offset function ........................................5-14
Auto peak hold [A.Peak] ..................5-9, 5-12, 7-9
Auto peak-to-peak hold [A.P-P] ................5-9, 7-9
Auto slant correction ......................3-19, 4-18, 8-8
Auto slant correction function ........................8-14
Auto-zero function ............................................5-4
Auto-zero input..........................................7-3, 7-6
AVG ................................................................4-13
AVG DISP .......................................................5-18
AVERAGE .........................................................5-8
Average hold [AVG.H] ..............................5-9, 7-9
Average measurement time...........7-13, 7-14, 9-6
Averaging .......................................................4-17
Averaging response time .................................9-6
Averaging time .................................................9-6
Index
A-11
E LT-9001-IM
Note: Pages marked in BOLD print refer to RS232C parameters, settings, etc.
Appendices
LT-9000-M-APP-E.qxd 10.4.8 6:02 PM ページA-11