Extron Electronics MAV Plus Series User Guide - Manual (Page 106)

Command and Response Table for SIS Commands (continued)
Command Function SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
View ties, gain, volume, mutes, and presets (continued)
View output mutes E VM } X1@ 1 X1@ 2 ... X1@ n ] Each X1@ response is the mute status
of an output, starting from output 1.
n = the maximum number of outputs.
Example:
CrossPoint 450 Plus 3232 HVA
E
VM
} Mut00001000000230000000000000000000 ]
Output 5 video, output 12 audio, and
output 13 video and audio are muted.
All other outputs are unmuted.
NOTE: The “Mut” portion of the response appears only when the switcher is in Verbose mode 2 or 3. See the Verbose mode command
on page 109 .
View video global preset
configuration EX(
*
X@
*1VC
} X! n •
X!
n +1 •...•
X!
n +15 •Vid
]
Show preset X( video configuration.
Show the input ( X! ) tied to 16 sequential
outputs, starting from output X@ .
Command description:
Response description: preset #*starting output # (StO#)*1(=video)VC
input # (I#) tied to StO#•I# tied to StO#+1•I# tied to StO+2• ... •I# tied to StO+15•Vid
]
NOTES:
• The starting output number ( X@ ) should always be “ 1 ” for matrix sizes of 16 outputs or smaller.
• EX( * X@ *1VC } where X( = 0 returns the current video configuration of the switcher.
Example:
MAV Plus 3232
E
4*17*1VC
}
17 Output:
Response = tied input:
input 24 tied to output 19
18 19 20 21 22 23 24 25 26 27 28
08•08•24•08•08•29•29•00•08•01•01•01•08•08•08•08•Vid
29 30 31 32
no tied input input 8 tied to output 29
Each position shown in the response is an output: left = starting output (17), right = starting output
+15 (32). The number in each position is the input tied to that output.
In this example, preset 4, video input 1 is tied to outputs 26 through 28; input 8 is tied to outputs
17, 18, 20, 21, 25, and 29 through 32; input 24 is tied to ouput 19; and input 29 is tied to outputs
22 and 23. No input is tied to output 24.
View audio global preset
configuration EX(
*
X@
*2VC
} X! n •
X! n+1 •...•
X! n+15 •Aud
]
Show preset X( audio configuration.
Show the input ( X! ) tied to 16 sequential
outputs, starting from output X@ .
Command description:
Response description: preset #*starting output # (StO#)*2(=audio)VC
input # (I#) tied to StO#•I# tied to StO#+1•I# tied to StO#+2• ... •I# tied to StO#+15•Aud
]
NOTES:
• The starting output number ( X@ ) should always be “ 1 ” for matrix sizes of 16 outputs or smaller.
• EX(
*
X@
*2VC
}
where
X(
= 0 returns the current audio configuration of the switcher.
Example:
MAV Plus 2412
E
15*1*2VC
}
01 Output:
Response = tied input:
input 1 tied to output 3
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16
no tied input no outputs
01•01•01•01•02•22•22•00•03•03•03•03•--•--•--•--•Aud
Each position shown in the response is an output: left = starting output (1),
right = starting output +15 (16). The number in each position is the input tied to that output.
(Outputs 13 through 16 are not present on the MAV Plus 2412.)
In this example, preset 15, audio input 1 is tied to outputs 1 through 4; input 2 is tied to output 5;
input 3 is tied to outputs 9 through 12; and input 22 is tied to outputs 6 and 7. No input is tied to
output 8. Outputs 13 through 16 are not present on this switcher.
NOTE: X! = Input number (for tie) 00 – (maximum number of inputs for your model) ( 00 = untied)
X@ = Output number 01 – (maximum number of outputs for your model)
X( = Global or room preset number 00 - 32 ( 00 = current configuration for view only)
X1@ = Video/audio mute: 0 = no mutes 1 = video mute 2 = audio mute 3 = video and audio mute
CrossPoint and MAV Series Matrix Switchers • Programming Guide 100