Det-Tronics EQP Fire and Gas Detection/Releasing System - Manual (Page 2)

Section 1 - Safety
Alert MessAges ..............................................................1-1
Section 2 - Introduction
sYsteM DesCrIPtION ...................................................... 2-1
Communications loop .................................................. 2-1
lON Communication Heartbeat .................................... 2-2
theory of Operation ...................................................... 2-2
Controller logs .............................................................. 2-4
Controller User logic .................................................... 2-4
Communication Network Fault Operation ..................... 2-4
Multiple Wiring Faults .................................................... 2-5
MAJOr COMPONeNt DesCrIPtIONs ............................. 2-5
system Controller .......................................................... 2-5
local Operating Network (lON) .................................... 2-6
Network extenders ................................................ 2-6
eQ21xxPs series Power supplies and
eQ2100PsM Power supply Monitor ...................... 2-7
eQP21xxPs(–X) Power supplies and
eQP2410Ps(–P) Converter ...........................................2-7
eQ2220gFM ground Fault Monitor ......................................2-7
Field Devices ................................................................. 2-7
Flame Detectors .................................................... 2-7
eQ3730eDIO enhanced Discrete I/O Module ....... 2-8
eQ3700 8 Channel DCIO Module ......................... 2-8
eQ3720 8 Channel relay Module ......................... 2-9
eQ3710AIM Analog Input Module ......................... 2-9
eQ3740IPM Intelligent Protection Module ........... 2-10
eQ3750AsH Addressable smoke & Heat Module .. 2-10
eQ25xxArM Agent release Module ....................2-11
eQ25xxsAM signal Audible Module .................... 2-12
eQ22xxIDC series Initiating Device Circuit ......... 2-12
eQ22xxDCU / eQ22xxDCUeX Digital
Communication Units ................................... 2-13
PIreCl PointWatch eclipse ................................ 2-13
OPeCl Open Path eclipse .................................. 2-13
UD10 DCU emulator ........................................... 2-13
Section 3 - Installation
sAFetY sYsteM DesIgN reQUIreMeNts .................... 3-1
Identifying the Area of Protection .................................. 3-1
Identifying Wiring, Network (lON), and system Power
requirements ........................................................ 3-1
general Wiring requirements................................ 3-1
Power Wiring .......................................................... 3-1
system Wiring (AteX and IeCex) ......................... 3-1
Determining Power requirements ......................... 3-3
eQ211xPs, eQ213xPs and eQ217xPs Power
supplies ......................................................... 3-5
Backup Battery ...................................................... 3-5
Battery Charger ..................................................... 3-5
eQP21x0Ps(–X) Power supplies .......................... 3-6
eQP2410Ps(–P) Converter ................................... 3-6
Determining Power requirements ......................... 3-7
shield grounding ................................................... 3-8
Junction Box grounding ........................................ 3-8
response time vs. system size ............................ 3-8
Moisture Damage Protection ................................. 3-8
electrostatic Discharge .......................................... 3-8
grOUND FAUlt MONItOr (gFM) INstAllAtION ........... 3-8
Mounting ................................................................ 3-8
Wiring .................................................................... 3-8
NetWOrk AND NetWOrk eXteNDer INstAllAtION ......3-9
Mounting ................................................................ 3-9
Wiring .................................................................... 3-9
INItIAtINg DevICe CIrCUIt (IDC) INstAllAtION .........3-11
eQ22xxIDC series Initiating Device Circuit ....................... 3-11
Mounting ...............................................................3-11
Wiring ...................................................................3-11
eQ22xxIDCgF series Initiating Device Circuit ground
Fault ..................................................................... 3-12
Mounting .............................................................. 3-12
Wiring .................................................................. 3-12
eQ22xxIDCsC series Initiating Device Circuit short
Circuit .................................................................. 3-13
Mounting .............................................................. 3-13
Wiring .................................................................. 3-13
Table of Contents