Rice Lake 880 Performance Series Indicator/Controller Technical/Service Manual User Manual
880 performance series, Technical/service manual
Advertising
Table of contents
Document Outline
- About This Manual
- 1.0 Introduction
- 1.1 Safety
- 1.2 Operating Modes
- 1.3 Front Panel Display
- 1.4 Indicator Operations
- 1.4.1 Toggle Gross/Net Mode
- 1.4.2 Toggle Units
- 1.4.3 Zero Scale
- 1.4.4 Acquire Tare
- 1.4.5 Remove Stored Tare Value
- 1.4.6 Preset Tare (Keyed Tare)
- 1.4.7 Print Ticket
- 1.4.8 Front Panel Setup
- 1.4.9 Displaying Audit Trail Information
- 1.4.10 Setpoints
- 1.4.11 Set Time and Date
- 1.4.12 Display Accumulator
- 1.4.13 Clear the Accumulator
- 1.4.14 Display Tare
- 2.0 Installation
- 2.1 Unpacking and Assembly
- 2.1.1 Parts Kit Components
- 2.2 Panel Mount Installation
- 2.2.1 Mounting the Controller Assembly Remotely
- 2.3 Controller Box Disassembly
- 2.3.1 Remove Backplate of Controller Assembly
- 2.4 Display Board Replacement
- 2.5 Cable Connections
- 2.5.1 Load Cells
- 2.5.2 Power Connections
- 2.5.3 Serial Communications – Port 1 (COM)
- 2.5.4 USB Device Communications – Port 2 (USBCOM)
- 2.6 USB Host
- 2.7 Ethernet Communications
- 2.8 CPU Board
- 2.9 Audit Trail and the Audit Jumper
- 2.10 Board Replacement
- 2.11 Digital I/O
- 2.12 Legal for Trade Sealing
- 2.13 Option Cards
- 2.14 Battery Replacement
- 2.15 Replacement Parts
- 3.0 Configuration
- 3.1 Configuration Methods
- 3.1.1 Revolution Configuration
- 3.1.2 EDP Command Configuration
- 3.1.3 User Setup Menu
- 3.1.4 Alphanumeric Entry Procedure
- 3.2 Menu Structures and Parameter Descriptions
- 3.2.1 Audit Menu
- 3.2.2 Setup Menu
- 3.2.3 Scale Menu
- 3.2.4 FORMAT Menu
- 3.2.5 Calibration Menu
- 3.2.6 Feature Menu
- 3.2.7 Region Menu
- 3.2.8 Ports Menu
- 3.2.9 Com Menu
- 3.2.10 Ethernet Communications Menu
- 3.2.11 USB Host
- 3.2.12 Print Format Menu
- 3.2.13 Setpoints Menu
- 3.2.14 Digital Input Menu
- 3.2.15 Analog Output Menu
- 3.2.16 Version Menu
- 4.0 Calibration
- 4.1 Front Panel Calibration
- 4.1.1 Five-point linearization
- 4.1.2 Rezero
- 4.2 LAST – Calibrating Zero Without Removing Test Weights
- 4.3 TEMP – Establishing a Temporary Zero for Calibrating a Loaded Scale
- 4.4 Adjusting Final Calibration (Trimming)
- 4.5 Gravity Compensation
- 4.6 EDP Command Calibration
- 4.7 Revolution® Calibration
- 5.0 Using Revolution®
- 6.0 EDP Commands
- 7.0 Print Formatting
- 8.0 Setpoints
- 9.0 Ethernet and USB
- 9.1 Ethernet Server/Client Connections
- 9.1.1 Direct Connection from a PC to the 880 Ethernet Server without a network (Ad-Hoc)
- 9.1.2 PC Connection to the 880 Ethernet Server Through a Network Switch or Router (Infrastructure)
- 9.1.3 Connection to a Remote Host - Demand Print to an Ethernet Printer
- 9.1.4 Connecting to a Remote Host - Stream weight data to an Ethernet Remote Display
- 9.1.5 Connecting to a Remote Host, Stream/Demand Data to Remote Ethernet-to-RS-232 Device Server
- 9.2 USB Host
- 9.2.1 Using a USB Keyboard
- 9.2.2 USB Memory storage
- 10.0 Appendix
- 10.1 Error Messages
- 10.1.1 Displayed Error Messages
- 10.2 Using the HARDWARE Command
- 10.3 ERROR Commands Output
- 10.4 Status Messages
- 10.5 TARE and ZERO Key Functions
- 10.6 Data Formats
- 10.6.1 Stream Serial Data Format
- 10.6.2 Print Output Serial Data Format
- 10.6.3 RS-485 Data Formats
- 10.7 Custom Stream Formatting – Input/Output
- 10.8 Stream Formatting Examples
- 10.8.1 Toledo 8142 Indicator
- 10.8.2 Cardinal 738 Indicator
- 10.8.3 Weightronix WI 120 Indicator
- 10.9 ASCII Character Chart
- 10.10 Digital Filtering
- 10.10.1 Sample Rate:
- 10.10.2 Digital Filter:
- 10.11 Analog Output Calibration
- 10.12 Specifications
- 880 Limited Warranty
- For More Information