Recording time codes and user bits – Panasonic AG-HPX250EN User Manual
Page 71
71
Shooting
Recording time codes and user bits
When SYSTEM MODE is set to 1080-59.94i, 720-59.94P, 480-59.94i
System setting status
Recorded TC
Output TC
Displayed
TC
Recorded UB
Output UB
SYSTEM
MODE
REC
SIGNAL
REC FORMAT
CAMERA
MODE
FRAME
RATE
LTC
VITC
TC OUT
LTC and
VITC
embedded
in HD SDI
TC tc (24/30
conversion)
LTC UB
VITC UB
TC IN/OUT
connector
UB
*1
LTC UB
embedded
in HD SDI
*1
VITC UB
embedded
in HD SDI
1080-
59.94i
CAMERA
DVCPROHD/60i
60i, 30P
—
R-RUN/F-RUN
*3
DF/NDF
30 frames
Same as
LTC
value
Outputs
LTC
Outputs
LTC
TC:
30 frames
tc:
24 frames
Follows UB
MODE.
·In ‘EXT’
slaves to UB
in TC IN/OUT
connector
Frame rate
data
Outputs
LTC UB
Outputs
LTC UB
Frame
rate data
(60i)
1 to 30
FRAME
24P, 24PA —
R-RUN/F-RUN
*5
NDF locked
30 frames
AVC-I100/60i
AVC-I50/60i
—
—
R-RUN/F-RUN
*3
DF/NDF
30 frames
Outputs
LTC
Outputs
LTC
1 to 30
FRAME
AVC-I100/30PN
AVC-I50/30PN
—
—
R-RUN/F-RUN
*3
DF/NDF
30 frames
Outputs
LTC
Outputs
LTC
30 FRAME
Other than
30 FRAME
R-RUN locked
DF/NDF
Every active
frame
30 frames
Matches
recorder
TC at
start of
recording
30 frames/
s
Matches
recorder
TC at
start of
recording
30 frames/
s
AVC-I100/24PN
AVC-I50/24PN
—
—
R-RUN/F-RUN
*7
NDF locked
24 frames
Converts
and outputs
LTC to 30
frames
Converts
and outputs
LTC to 30
frames
Recording
TC:
24 frames
Playback
TC:
24 frames
tc:
30 frames
Output
adjusted
to Over
60i based
on LTC
UB
Output
adjusted
to Over
60i based
on LTC
UB
24 FRAME
Other than
24 FRAME
R-RUN locked
NDF locked
Every active
frame
24 frames
Matches
recorder
TC at
start of
recording
30 frames/
s
Matches
recorder
TC at
start of
recording
30 frames/
s
1394
DVCPROHD/60i
—
—
R-RUN/F-RUN
*2
DF/NDF
30 frames
Records
VAUX TC
in 1394
input at
all times
*6
Outputs
LTC
Outputs
LTC
TC:
30 frames
tc:
24 frames
Follows UB
MODE.
·In ‘EXT’
slaves to
LTC UB in
1394 input
Records
VITC UB in
1394 input at
all times
Outputs
LTC UB
Outputs
LTC UB
Outputs
VITC UB
*1: When UB MODE is FRM. RATE, playback of native clips is the pulldown frame rate read from VITC UB.
*2: In Free Run mode, it is slaved to the value input to the DVCPRO/DV connector. It does not slave it to
the time code from the TC IN/OUT connector.
*3: In Free Run mode, it is slaved to the time code input to the TC IN/OUT connector.
*5: In Free Run mode, it is slaved when TC input to the TC IN/OUT connector is non-drop frame. But not
slaved to it during recording.
*6: VAUX TC is time code recorded in the video AUX area in the DVC format.
*7: In Free Run mode, it is slaved to the time code input to the TC IN/OUT connector, whose value is
converted to 24 frames when it was NDF 30 frames. But not slaved to it during recording.