Rockwell Automation 1770, D17706.5.16 Ref Mnl DF1 Protocol Command - Manual (Page 90)

7–3 Communication Commands
Publication 1770Ć6.5.16 - October 1996
Command Page Processors FNC CMD
MicroĆ
Logix
1000
SLC
500
Ã
SLC
5/03 SLC
5/04 1774Ć
PLC
PLCĆ2 PLCĆ3 PLCĆ5
PLCĆ5
/250 PLCĆ5/
VME
protected typed file write 0F AF 4 4 4 4 7-16
protected typed logical read
with three address fields
0F A2 4 4 4 4 4 7-17
protected typed logical write
with three address fields
0F AA 4 4 4 4 4 Á 7-18
protected write 00 Â
4 4 4 4 7-19
read bytes physical 0F 17 4 4 ➄ 4 7-19
read diagnostic counters 06 01 4 4 4 4 4 4 4 4 4
➄ 7-19
reset diagnostic counters 06 07 4 4 4 4 4 4 4 4 4
➄ 7-22
read link parameters 06 09 4 4 4 4 7-20
readĆmodifyĆwrite 0F 26 4 4
➄
4 7-20
readĆmodifyĆwrite N 0F 79 4
➄ 7-21
read section size 0F 29 4 4 4 ➄ 7-22
restart request 0F 0A 4 7-23
return edit resource 0F 12 4 7-24
set CPU mode 0F 3A 4 4 4 ➄ 7-26
set data table size 06 08 4 7-24
set ENQs 06 06 4 4 4 ➀ 4 ➄ 7-25
set link parameters 06 0A 4 4 4 4 7-25
set NAKs 06 05 4 4 4 ➀ 4 ➄ 7-25
set timeout 06 04 4 4 4 ➀ 4 ➄ 7-27
set variables 06 02 4 4 4 ➀ 4 ➄ 7-27
shutdown 0F 07 4 7-28
typed read 0F 68 4 4 4 4 4 7-28
typed write 0F 67 4 4 4 4 4 7-30
unprotected bit write 05 Â 4 4 4 4 4 7-30
unprotected read 01 Â 4 4 4 4 4 4 4 4 4 7-31
unprotected write 08 Â 4 4 4 4 4 4 4 4 4 7-32
upload all request (upload) 0F 53 4 4 ➄ 4 7-33
upload completed 0F 55 4 4 ➄ 4 7-34
upload 0F 06 4 7-34
word range read 0F 01 4 4 4 7-34
word range write 0F 00 4 4 4 7-35
write bytes physical 0F 18 4 4
➄
4 7-35
À This command cannot be executed by channel 0 of a PLCĆ5/11, Ć5/20, Ć5/30, Ć5/40, Ć5/60, or Ć5/80 processor.
Á The following processors can initiate these commands but cannot respond to them:
Processor Series/Revision
Processors:
Series A / revision M PLCĆ5/40, Ć5/40L, Ć5/60, Ć5/60L
Series A / revision J PLCĆ5/30
Series A / revision H PLCĆ5/11, Ć5/20
Series B / revision J PLCĆ5/40, Ć5/40L, Ć5/60, Ć5/60L
Series C / revision G PLCĆ5/11, Ć5/20, Ć5/20E, Ć5/30, Ć5/40, Ć5/40L, Ć5/V40, Ć5V40L, Ć5/60, Ć5/60L, Ć5/80, Ć5/80E, Ć5/V80
 This command has no FNC byte.
à SLC 500 refers to any SLC 500, SLC 5/01, SLC 5/02, SLC 5/03, or SLC 5/04 processor.
➄ Receive only. Processors with this note cannot send the command; they receive the command from a computer.