Document Outline

• 1756-UM534B-EN-P, ControlLogix Remote I/O Communication Module User Manual
• Summary of Changes
  • New and Updated Information
• Table of Contents
• Preface
  • Introduction
  • Who Should Use This Manual
  • Information Found in This Manual
  • Additional Resources
• Chapter 1 - The 1756-RIO Module-Getting Started
  • Introduction
  • 1756-RIO Module Components
  • 1756-RIO Module Requirements
  • The 1756-RIO Modes
  • Prepare the Module
  • Install the Software
  • Install the Add-on Profile
  • Create the RSLogix 5000 Project
    • Configure the Controller
    • Add the 1756-RIO Module
    • Enter the RPI
  • Set Communication Path and Download to the Controller in the RSLogix 5000 Project
  • Launch the Configuration Tool and Select the Module Mode
    • Launch the 1756-RIO Configuration Tool
• Chapter 2 - Configure Scanner Mode
  • Introduction
  • Configure Scanner Summary
  • Set the Baud Rate
  • Autoconfigure Racks
  • Manually Configure Racks
    • Matching Configuration Tool Settings with Module Settings
    • Resize a Rack
    • Delete a Rack
  • Configure Block Transfer Modules
  • Map I/O Data
    • Automatic Mapping
    • Manually Map Discrete (rack) Data
    • Manually Map Block Transfer Data
    • Re-Map Command
    • Clear Mappings
• Chapter 3 - Configure Adapter Mode
  • Introduction
  • Configure Adapter Summary
  • Set the Baud Rate
  • Autoconfigure Racks
    • Perform the AutoConfiguration
    • Active Versus Monitored Racks on the Network
  • Manually Configure Racks
    • Resizing Racks
    • Delete Racks
  • Configure Block-transfer Modules
  • Map I/O Data
    • Automatic Mapping
    • Manually Map Discrete Data
    • Re-Map Command
    • Clear Mappings
• Chapter 4 - Link Module Configuration with RSLogix 5000 Project
  • Introduction
  • Commission Summary
  • Aliases
    • Export Aliases in Scanner Mode
    • Export Aliases in Adapter Mode
    • Use Monitor Mode to Upgrade an Existing System to a ControlLogix System
  • Manage Configurations
    • Download and Upload Configurations
    • Save Configurations to Disk
    • Archive Configurations
• Chapter 5 - Monitor Remote I/O
  • Introduction
  • Commission Summary
  • Scan Mode and Monitor Mode
    • Scan Remote I/O in Scanner Mode
    • Monitor Remote I/O in Adapter Mode
  • Monitor Discrete Inputs and Outputs
    • Monitor Discrete Inputs in Scanner Mode
    • Monitor Discrete Outputs in Scanner Mode
    • Monitor Discrete Inputs in Adapter Mode
    • Monitor Discrete Outputs in Adapter Mode
    • Monitor Discrete Active Inputs in Adapter Mode
  • Monitor Block Transfers
    • Monitor Block Transfers in Scanner Mode
    • Monitor Block Transfers in Adapter Mode
  • Export Scanner Configurations
    • Monitor Mode
  • Other Diagnostics
    • Monitor Diagnostic Counters in Scanner Mode
    • Monitor Diagnostic Counters in Adapter Mode
    • Module Scanner Log
    • Clear Diagnostics
    • Fatal Errors
• App A - Scanner Mode I/O Map
  • Discrete Input Data
  • Discrete Output Data
  • Block Transfer Input
  • Block Transfer Output
• App B - Adapter Mode I/O Map
  • Discrete Data
    • Discrete Input Data
    • Discrete Output Data on Monitored or Active Racks
  • Block Transfer Modules
    • Block Transfer Read Data on Monitored or Active Racks
    • Block Transfer Write Data on Monitored or Active Racks
• App C - Block Transfer Module Templates
  • Block Transfer Template Records
  • Block Transfer Lengths
  • Parameters
  • Parameter Examples
  • Aliases
• App D - Troubleshooting Display and Status Indicators
  • Alphanumeric Display
  • Status Indicators
    • RIO Status Indicator – Remote Devices Status
    • CLX Status Indicator – ControlBus Status
    • OK Status Indicator – Module Health
    • The Debug Log
    • Fatal Errors
    • Watchdog and Jabber Inhibit
    • Updating the Firmware
• Quick Start
  • ControlLogix System Quick Start
• Index
  • Symbols
  • Numerics
  • A
  • B
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • J
  • L
  • M
  • N
  • O
  • P
  • Q
  • R
  • S
  • T
  • U
• Back Cover