Rockwell Automation 5370 Color CVIM Communications Manual - Manual (Page 48)

Chapter 4
Using the Remote I/O Link
4–11
Table 4.C
Color CVIM Module Remote I/O Outputs (PLC to Color CVIM Module)
if Color CVIM Module is Rack 02
BIT
07
–––
17
06
–––
16
05
–––
15
04
–––
14
03
–––
13
02
–––
12
01
–––
11
00
–––
10
W
O
R
D
(Reserved)*** (Reserved)*** (Not Used) (Not Used) (Not Used) (Not Used) (Not Used) (Not Used)
(Not Used)
1 = Config
Transfer 1 = I/O
Request 1 = Light pen
Request
(Not Used) 1 = Trigger
1 = Unlock
Setup 1 = Lock
Setup 20
(Not Used)
1 = Display
Stat 2 Page 1 = Display
Stat 1 Page 1 = Display
Results Page 1 = Display
I/O Page 1 = Display
All Tools 1 = Display
Failed Tools 1 = Display
Image Only
21
(Not Used) (Not Used) (Not Used) Halt on Reject
1 = Freeze
Next Image 1 = Freeze All
Rejects 1 = Freeze
First Reject Go on reject
21
1 = Enable
JMB Forces 1 = Disable
JMB Forces 1 = Enable
JMB Outputs 1 = Disable
JMB Outputs
(Not Used) (Not Used)
1 = Post 2nd
Half Results
to Remote I/O 1=Post 1st
Half Results
to Remote I/O
22
1 = Credit
Card Config.
(8’s bit)**** 1 = Credit
Card Config.
(4’s bit)**** 1 = Credit
Card Config.
(2’s bit)**** 1 = Credit
Card Config.
(1’s bit)**** 1 = RAM to
Credit Card 1 = Credit
Card to RAM 1 = RAM to
EEPROM 1 = EEPROM
to RAM
22
Toolset Active
(Normally Not
Used *****) Toolset Active
(Normally Not
Used *****) Toolset Active
(Normally Not
Used *****) Toolset Active
(Normally Not
Used *****) 1 = Last Block
(write Only) Block Transfer
Type * Block Transfer
Type * Block Transfer
Type *
23
1 = Block
Trnsfer Block
No. (128’s bit) 1 = Block
Trnsfer Block
No. (64’s bit) 1 = Block
Trnsfer Block
No. (32’s bit) 1 = Block
Trnsfer Block
No. (16’s bit) 1 = Block
Trnsfer Block
No. (8’s bit) 1 = Block
Trnsfer Block
No. (4’s bit) 1 = Block
Trnsfer Block
No. (2’s bit) 1 = Block
Trnsfer Block
No. (1’s bit)
23
1 = Force JMB
Output 8 ON** 1 = Force JMB
Output 7 ON** 1 = Force JMB
Output 6 ON** 1 = Force JMB
Output 5 ON** 1 = ForceJMB
Output 4 ON** 1 = Force JMB
Output 3 ON** 1=Force JMB
Output 2 ON** 1=Force JMB
Output 1 ON**
24
(Not Used) (Not Used)
1 = Force
JMB Output
14 ON** 1 = Force
JMB Output
13 ON** 1 = Force
JMB Output
12 ON** 1 = Force
JMB Output
11 ON** 1 = Force
JMB Output
10 ON** 1 = Force
JMB Output 9
ON**
24
1 = Force
JMB Output 8
OFF** 1 = Force
JMB Output 7
OFF** 1 = Force
JMB Output 6
OFF** 1 = Force
JMB Output 5
OFF** 1 = Force
JMB Output 4
OFF** 1 = Force
JMB Output 3
OFF** 1 = Force
JMB Output 2
OFF** 1 = Force
JMB Output 1
OFF**
25
(Not Used) (Not Used)
1 = Force
JMB Output
14 OFF** 1 = Force
JMB Output
13 OFF** 1 = Force
JMB Output
12 OFF** 1 = Force
JMB Output
11 OFF** 1 = Force
JMB Output
10 OFF** 1 = Force
JMB Output 9
OFF**
25
1 = Reset
Counters 1 = Reset
Stats 1 = Page
Down 1 = Page Up 1 = Resume
Control
(Not Used) (Not Used) (Not Used)
26
(Not Used) (Not Used) (Not Used) (Not Used) (Not Used) (Not Used) (Not Used) (Not Used)
26
(Not Used) (Not Used) (Not Used) (Not Used) (Not Used) (Not Used) (Not Used) (Not Used)
27
(Not Used) (Not Used) (Not Used) (Not Used) (Not Used) (Not Used) (Not Used) (Not Used)
27
* Set these three bits to specify the type of block as follows: 001 = Results, 010 = Configuration, 100 = Template, 101 = Statistics,
111 = Programmable Results Block Write
** If both ON & OFF bits are set, the output is forced OFF.
*** Do not write to these bits.
**** The first configuration on the card is 0000. When writing configurations from card to Color CVIM, remember that a card is made up of 32K
slots, and the address is the address number of the slot (a 64K card contains two slots; a 512K card contains 16 slots). A complete image takes
12 slots.
**** *Used for Results and Stats Blocks only. Refer to page 4–17 for additional information.
Accessing Discrete
Bit Information (cont’d)