Interlogix XL LCD Keypad Plus Regional Settings Guide - Manual (Page 6)

xL Regional Settings Guide 21-3609E rev1.0 2
(remain on the premises with only the perimeter
protection on) or On (all protection turned on)
pressing the keypad button below them. Press the
right arrow key to browse through the Menu
Options. Selections such as Status (condition of
system), Bypass (disable a protection point),
History (alarm etc. history), My PIN (change your
PIN number), Users (edit system users), Test (test
the system), Config (edit the system’s program),
Time (adjust the LCD keypad’s Time and Date),
Verify (transmit an Okay signal if a false alarm
occurred), Arm/Disarm (set protection Off, Stay or
On). Select “Config” and press Ok.
• NOTE: Default MASTER (end) USER code is ID 01
or 001, PIN 7793. Default Service User ID 00 or
000, PIN 2482.
• “Config method” will appear. Using the arrows,
toggle between “Simplified” or “Advanced” for the
process to set up the system as required. If
Simplified is chosen, ordinary language menus will
appear to browse through and make selections to
make a basic system from. If Advanced is chosen,
special menus will appear to customize the system
into several unique forms of security requirements.
Logging On to a New UK ACPO System
ƒ
After the “CommsLost” keypad screen and 24822
has been entered, the screen will display that the
system is in alarm and needs to be re-set.
ƒ Enter the UK service user code: 000 and PIN:
1630 .
ƒ A user code and PIN for a second user will be
requested. Enter the Master User default code: 001
and PIN: 7793.
ƒ The next screen will request the date and time to
be entered.
ƒ The next screen will display that the system is in
alarm and enter ID to restore it.
ƒ The Master User codes can be entered however, if
a service user enters 000, the next screen will
request a Pin of the Day to log on. (Refer to the
“European and ACPO Installations” section of this
manual for “PIN of the Day” instructions.) After the
PIN of the Day is entered, a secondary user code
will be requested. The Master user codes can be
used again.
UK ACPO Pin of the Day
• The service user will call the Pin of the Day
program operator who can enter default “24822” as
the new system’s default Dealer ID until a unique
one can be entered at the keypad or downloaded
from the Director Software later.
• The service user enters random, 6 digit Pin of the
Day number given to them by the operator at the
keypad and can then access the system menus
and configurations.
Remote Connection
• If a Remote connection is selected, the next screen
will display a left or right arrow selection for IP or
the version of modem board plugged into the main
control module (e.g. World Wide Modem or IP
discussed later). IMPORTANT: When one of the
modems is used, it must be plugged into the main
control module before remote connection screens
can be viewed. Press the button below Ok.
• The next screen will ask to “Select country” for the
style of system configurations that are required for
different places in the world. Use the left-right arrow
keys to toggle through them. The selections are: N
(North) America, European, U.K., Aus/NZ
(Australia, New Zealand) and China/H.K. (Hong
Kong), Netherlands, Switzerland, France. Press the
button below Ok.
• The next screen will display an entry for a 6 digit
unique ID to identify this particular system.
000000
↓Save (unique id) • Press the button below
“Save” when the selection
has been made.
• The next screen will display an entry for a 6 digit
third party password. This is a special security
number that prevents unauthorized connection to
this main control module.
000000
↓Save (3rdPtPass) • Press the button below
“Save” when the selection
has been made.
• Next enter the phone number to contact and get a
system program, configuration download from the
Director Software computer.
The phone number can be preceded with P =pulse dialing
(default), or T =Tone dialing, and can include D =2 sec Delay, A
=Star key (tone dialing), # = Pound Sign (tone dialing), and/or W =
Wait for second dial tone. For Tone dialing, ensure the phone line
supports this. As the phone number is entered, the cursor will
automatically move to the next character entry position. Use the
left and right arrow keys to move the cursor back and forth in the
entry. Place the cursor under a character where a blank is
desired. Press the “_” selection on the “
0 Z_Q ” keypad key to
replace the character with a blank space.
_
↓Save (cfg tel #) • Press the button below
“Save” when the selection
has been made.
Download Config
Please wait...... • When Save is pressed,
the main control module
will attempt to dial the
config PC. Download Config
Dialing......
While the main control module is trying to get its
download, an asterisk: “
Â
” will appear between the
hour and the minute display on the time and date main
screen.