Interlogix XL LCD Keypad Plus Regional Settings Guide - Manual (Page 8)

xL Regional Settings Guide 21-3609E rev1.0 4
Special Regional Settings Keypad Operations
For all xL Security System keypad operations, refer to the “xL LCD Keypad User’s Guide”
North America
• Split Logs When the History menu is accessed on the keypad, the selections “All”, “Intrusion” and
“Category\Area\Area condition: On, Off, Stay\Area History” are available.
European
• If the system is not ready to arm when logging on to the keypad, the message: “check system” will appear on the
keypad screen. Protection points may be insecure or an equipment trouble condition could be present.
• Some trouble conditions can have an override placed on them so the system ignores them while some trouble
conditions can not have an override. An end user can place an override on some trouble conditions while they will
not be allowed to put an override on others. All trouble conditions allowed to have an override can have an override
placed on them by a service user however an end user must enter their user codes at the same time.
• Dual Custody A service user entering their user codes must also have an end user enter their user codes for the
service user to be able to service the system or access system programming through the keypad.
• Alarm/Trouble Condition Acknowledge When an alarm or trouble condition has occurred, after entering a user
code, the condition must be acknowledged.
− The alarm condition will continue to appear in the normal rotating keypad screens and ask to be acknowledged
each time the keypad is logged on to.
− In order to clear this condition, a service user must open the control box to activate its tamper switch and enter
their codes along with the end user’s codes at the keypad.
• Split Logs When the History menu is accessed on the keypad, the selections “All”, “Intrusion” and
“Category\Area\Area condition: On, Off, Stay\Area History” are available.
UK ACPO
• Dual Custody
− A service user entering their user code must also enter a Pin of the Day which they obtain from a designated Pin
of the Day operator. Refer to the “Logging On to a New UK ACPO System” and “UK ACPO Pin of the Day”
sections in this manual.
− A service user entering their user codes must also have an end user enter their user codes for the service user
to be able to service the system or access system programming through the keypad. Refer to the “Logging On to
a New UK ACPO System” and “UK ACPO Pin of the Day” sections in this manual.
• Alarm/Trouble Condition Acknowledge When an alarm or trouble condition has occurred, after entering a user
code, the condition must be acknowledged. When it is, the condition will reset.
• Split Logs When the History menu is accessed on the keypad, the selections “All”, “Intrusion” and
“Category\Area\Area condition: On, Off, Stay\Area History” are available.
Aus/NZ (Australia/New Zealand)
• Dual Custody Not Used.
• Split Logs When the History menu is accessed on the keypad, the selections “All”, “Intrusion” and
“Category\Area\Area condition: On, Off, Stay\Area History” are available.
China/HK (China/Hong Kong) CCC (China Compulsory Certification)
• Dual Custody A service user entering their user codes must also have an end user enter their user codes for the
service user to be able to service the system or access system programming through the keypad.
• Alarm/Trouble Condition Acknowledge When an alarm or trouble condition has occurred, all protection
inputs/trouble conditions will appear on the keypad screen by reviewing them using the keypad left/right arrows.
When the last condtion has appeared, the keypad will ask for an acknowledgement by pressing the keypad key
below “Ack”.
− The trouble condition will continue to appear in the normal rotating keypad screens as “Was in Tamper!”.
− In order to clear this condition, a service user must open the control box to activate its tamper switch and enter
their codes along with the end user’s codes at the keypad.
• Split Logs When the History menu is accessed on the keypad, the selections “All”, “Intrusion” and
“Category\Area\Area condition: On, Off, Stay\Area History” are available.
• Turning Protection On can not be done when the system’s AC Mains power is off or a tamper condtion exists. Only
a service user has the authority to place an override on an “AC Mains power is off” or tamper condition.