Datalogic Scanning 9500 User Manual
Magellan
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- Introduction
- Site Preparation and Installation
- Pre-Installation Considerations
- Checkstand Design
- Scanner Installation
- Scanner Maintenance
- References
- Scanner Usage
- Site Preparation Overview
- Ventilation and Spacing
- Service Access
- Power Installation
- Checkstand Preparation
- Counter Cutout
- Installation Overview
- Remote Scale Display Placement/Installation
- Set-Up & Installation
- System Power-Up Recap
- Operation and Maintenance
- Problem Isolation
- Calibration
- Programming
- Introduction to Label Programming
- Understanding the Basics
- Integrating the Scanner With Your Host System
- Programming Overview
- LED and Beeper Indicators
- If You Make a Mistake...
- General Scanner and Scale Features
- Double Read Timeout
- Laser Timeout
- Motor Timeout
- Green LED Idle State
- Scanner Button Options
- Power-up Beep Control
- Good Read Beep Control
- Good Read Beep Frequency
- Good Read Beep Length
- Good Read Beep Volume
- Good Read When to Indicate
- Scale Enable
- Scale Country Mode
- Scale Enforced Zero Return
- Scale Interface Type
- Scale Motion Level Filter
- Scale LED Enable
- Remote Display - Enable/Disable
- Aux Port Mode
- Laser Failure Mode
- Productivity Index Reporting (PIR)/Cashier Training (CT)
- EAS Features
- Interface Related Features
- IBM Features
- RS-232 Features
- RS-232 Baud Rate
- RS-232 Number of Data Bits
- RS-232 Number of Stop Bits
- RS-232 Parity
- RS-232 Hardware Control
- RS-232 Intercharacter Delay
- RS-232 Software Flow Control
- RS-232 Host Echo
- RS-232 Host Echo Quiet Interval
- RS-232 Ignore Host Commands
- RS-232 TTL
- RS-232 TTL Invert
- RS-232 Beep on ASCII BEL
- RS-232 Beep After Weigh
- RS-232 Beep on Not on File
- RS-232 ACK NAK Enable
- RS-232 ACK Character
- RS-232 NAK Character
- RS-232 Retry on ACK NAK Timeout
- RS-232 ACK NAK Timeout Value
- RS-232 ACK NAK Retry Count
- RS-232 ACK NAK Error Handling
- RS-232 Label ID Control
- Single Cable RS-232 Options
- Symbology Programming
- UPC-A Enable
- UPC-E Enable
- EAN-13 Enable
- EAN-8 Enable
- Other UPC/EAN Options
- GTIN Enable
- RSS-14 Enable
- RSS Expanded Enable
- Code 39 Enable
- Code 39 Start Stop Character Transmission
- Code 39 Check Character Calculation
- Code 39 Check Character Transmission
- Code 39 Full ASCII
- Code 39 AIM ID
- Code 39 Label ID
- Code 39 Length Control
- Code 39 Maximum Label Length
- Code 39 Minimum Label Length
- Code 39 Fixed Length 1
- Code 39 Fixed Length 2
- Code 39 Stitching
- Pharmacode 39 Enable
- Code 128 Enable
- EAN-128 Enable
- Interleaved 2 of 5 (I 2 of 5) Enable
- Codabar Enable
- Codabar Start Stop Character Transmission
- Codabar Start Stop Character Set
- Codabar Start Stop Character Match
- Codabar Check Character Calculation
- Codabar Check Character Transmission
- Codabar AIM ID
- Codabar Label ID
- Codabar Length Control
- Codabar Maximum Label Length
- Codabar Minimum Label Length
- Codabar Fixed Length 1
- Codabar Fixed Length 2
- Codabar Stitching
- Code 93 Enable
- MSI/Plessey Enable
- MSI/Plessey Check Character Calculation
- MSI/Plessey Number of Check Characters
- MSI/Plessey Check Character Transmission
- MSI/Plessey AIM ID
- MSI/Plessey Label ID
- MSI/Plessey Length Control
- MSI/Plessey Maximum Label Length
- MSI/Plessey Minimum Label Length
- MSI/Plessey Fixed Length 1
- MSI/Plessey Fixed Length 2
- MSI/Plessey Stitching
- Standard 2 of 5 Enable
- Standard 2 of 5 Check Character Calculation
- Standard 2 of 5 Check Character Transmission
- Standard 2 of 5 AIM ID
- Standard 2 of 5 Label ID
- Standard 2 of 5 Length Control
- Standard 2 of 5 Maximum Label Length
- Standard 2 of 5 Minimum Label Length
- Standard 2 of 5 Fixed Length 1
- Standard 2 of 5 Fixed Length 2
- Standard 2 of 5 Stitching
- LED/Beeper Indications & Controls
- Cable Information
- Keypad
- Host Commands
- Factory Defaults
- Handheld Data Format Requirements