Adjust the torch position -40 – Hypertherm MAX200 Machine Torch Plasma Arc Cutting System User Manual
Page 64
3-40
MAX200
Instruction Manual
14
SETUP
WARNING
Disconnect all power to the MAX200 before adjusting the torch. Failure to do so could result in
eye or bodily injury due to accidental firing or movement of the torch.
Adjust the Torch Position
Before using the machine torch system, the torch must be adjusted for the torch-to-work distance for the metal to
be cut. To adjust the torch, perform the following procedure.
Note:
Two people may be required to perform the torch position adjustment.
1. Retract the torch from the work at least 3-4 inches.
2. Manually extend probes fully by pulling down on the plastic mounting yoke.
3. Adjust the position of the torch in the mounting bracket by loosening the securing bolt and positioning the torch
so that the torch shield is within 1/16 to 1/8 inch of the extended probe plastic caps. Use a straight edge to
determine this (see Figure 3-19). Secure the torch in the mounting bracket by tightening the securing bolt.
Figure 3-19
Torch Standoff Adjustment Setup
Torch
Torch
Shield
Inductor
Probe
- THC ArcGlide
- 80669C Rev.2
- HD3070 Plasma Arc Cutting System w/ Automatic Gas Console
- V9 Series Phoenix Rev.11
- MicroEDGE Pro Shape Cutting Control Rev.2
- HD4070 Rev.1
- HPR260 Manual Gas Preventive Maintenance Program Rev.5
- Shape Cutting Control
- PHC Sensor
- HTA Rev 6.00 Operators Manual
- HTA Rev 6.00 Install Guide
- THC Control Board Replacement
- THC Plasma Interfacer Upgrade
- THC X-Y Table Product Configuration
- D845GEBV2
- HRT2
- HRT
- Duramax Hyamp Long Handheld Torches
- Duramax Hyamp Robotic Torch
- HyIntensity Fiber Laser Rev.3
- PCBS-0124
- SuperMicro 370SBA 533Mhz
- LR2075
- Phoenix 8.0
- LH2100
- HD3070 w/ Automatic Gas
- HD3070 w/Manual Gas
- HD4070 Rev.8
- HD4070 Product Configuration
- HPR130 Auto Gas Preventive Maintenance Program
- HPR800XD Auto Gas Preventive Maintenance Program Rev.1
- HPR800XD Auto Gas Rev.2
- HPRXD Short Torch with Integrated Lead Rev.1
- HT4001
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm
- HT400 Air Injected Water Muffler System
- H401 Power Supplies
- MAX40 Remote Switch
- HT4100 Plasma Arc Cutting System Operating
- HT4001 Plasma Arc Cutting System
- HSD130 HySpeed Plasma
- HySpeed HT2000 Plasma Arc Cutting System Rev.7
- HT2000-200 Volt
- HT2000 Water Muffler
- HT2000LHF Product Configuration
- HD4070 Ignition Console
- HT4400 Plasma Arc Cutting System Gas Panel
- HT200LHF-200 Volt HySpeed
- HT4400 HySpeed Product Configuration
- HT4400 HySpeed
- MAX200 Product Configuration
- HT4400 HySpeed Plasma Arc Cutting System
- MAX200 Service Manual
- MAXPRO200 Preventive Maintenance Program
- Powermax105 Service Manual
- RT60 Retrofit Torch
- Powermax190c Operator Manual
- Powermax30 Operator Manual
- Powermax600 Operator Manual
- Powermax1000 Service Manual
- Powermax65 Service Manual Rev.1
- Powermax1650 Service Manual
- Powermax190c Service Manual
- Powermax350 Service Manual
- Powermax1250 Service Manual
- Powermax30 Service Manual
- Powermax600 Service Manua
- Powermax900 Service Manual
- PAC500 Flow Switch Upgrade
- RoboTester Troubleshooting Kit
- PAC500 Water Injection Plasma Cutting System
- THC2 Torch Height Control
- HD1070 Product Configuration
- PAC500 Product Configuration
- Powermax30 Service Manual power board replacement procedure update
- Powermax30 AIR Service Manual
- Powermax125 Service Manua
- Powermax30 XP Service Manual
- Powermax45 Service Manual
- SensorOHC
- Powermax190c Troubleshooting Guide