Teac HS-2000 - Manual (Page 13)

TASCAM HS-2000
13
2 − Names and functions of parts
Rear panel
h ANALOG IN [LINE] connectors (L/R)
These are balanced analog XLR connectors for line
input.(1: GND, 2: HOT, 3: COLD)
j DIGITAL IN [LINE] connector
This balanced XLR connector is for digital audio input
in AES3-2003/IEC60958-4 (AES/EBU) or IEC60958-3 (S/
PDIF) format.
Sampling frequencies of 88.2 and 96 kHz are
transmitted at double speed. Sampling frequencies of
176.4 and 192 kHz are transmitted at quadruple speed.
The built-in sampling rate converter can handle 32–
192 kHz.
k ANALOG OUT [MONITOR] connectors (L/R)
These balanced analog XLR connectors output the left
and right monitoring signals. (1: GND, 2: HOT, 3: COLD)
l RS-232C connector
Connect an external controller, for example, to this
9-pin
D-sub connector for RS-232C serial control.
NOTE
It cannot be used at the same time as the RS-422
connector. (See “RS-232C page” on page 107.)
;
PARALLEL connector
Connect a TASCAM RC-SS20 or other external
controller to this 25-pin D-sub parallel control
connector.
z AC IN connector
Connect the included power cord here.
x ANALOG OUT [LINE] connectors (L/R)
These balanced analog XLR connectors are for line
output. (1: GND, 2: HOT, 3: COLD)
c DIGITAL OUT [LINE] connector
This balanced XLR connector is for digital audio output
in AES3-2003/IEC 60958-4 (AES/EBU) format.
Sampling frequencies of 88.2 and 96 kHz are
transmitted at double speed. Sampling frequencies of
176.4 and 192 kHz are transmitted at quadruple speed.
v REMOTE connector
Connect a TASCAM RC-HS32PD or RC-HS20PD remote
control (sold separately) here.
CAUTION
Never connect this to a network using an Ethernet cable.
Doing so could damage this unit or network equipment.
b
RS-422 connector
Connect an external controller, for example, to this
9-pin D-sub connector for RS-422 serial control.
NOTE
It cannot be used at the same time as the RS-232C
connector. (See “RS-422 page” on page 108.)
n
TIMECODE INPUT connector
This balanced XLR connector is for SMPTE timecode
input.
m TIMECODE OUTPUT connector
This balanced XLR connector is for SMPTE timecode
output.
, WORD/VIDEO IN connector
This BNC-type connector accepts a word clock signal
(44.1kHz, 48kHz, 48kHz pull-down, 48kHz pull-up,
88.2kHz, 96kHz, 176.4kHz, 192kHz) or a video reference
signal (NTSC/PAL black burst signal, HDTV Tri-Level
signal).
Use the switch to turn the integral 75Ω terminator on
or off.
. WORD/VIDEO THRU/OUT connector [cut “WORD”]
This BNC-type connector outputs a word clock signal
(44.1kHz, 48kHz, 48kHz pull-down, 48kHz pull-up,
88.2kHz, 96kHz, 176.4kHz, 192kHz or thru) or a video
reference signal (IN connector signal thru only).
Use the THRU/WORD OUT switch to set the signal
output.
/ 75Ω ON/OFF/THRU/WORD OUT switch
Use this three-way switch to make one of the following
settings.
Terminator OFF and WORD/VIDEO THRU
Terminator OFF and WORD OUT (no VIDEO OUT)
Terminator ON and WORD OUT (no VIDEO OUT)
! ETHERNET connector
Use this Ethernet connector to connect the unit with
a network for file transfer and to control this unit from
another device on the network.