Teac HS-2000 - Manual (Page 151)

TASCAM HS-2000
151
18 – Specifications
Digital audio inputs and outputs
DIGITAL IN [LINE] connector
Connector: XLR-3-31
Input signal voltage amplitude: 200 mVp-p to 10 Vp-p
Input impedance: 110 Ω ±20%
Format: AES3-2003/IEC60958-4 (AES/EBU)
IEC60958-3 (S/PDIF)
Supported sampling frequencies:
44.1/47.952/48/48.048/88.2/96/176.4/192kHz
(single/double/quad)
(47.952/48.048: 48 kHz ±0.1% pull-down/pull-up)
Note: When SRC is ON, the receivable range is 32–192
kHz.
DIGITAL OUT [LINE] connector
Connector: XLR-3-32
Output voltage: 2–5 Vp-p
Output impedance: 110 Ω ±20%
Format: IEC60958-4 (AES3-2003, AES/EBU)
Supported sampling frequencies:
44.1/47.952/48/48.048/88.2/96/176.4/192kHz
(single/double/quad)
(47.952/48.048: 48 kHz ±0.1% pull-down/pull-up)
Control inputs and outputs
RS-422 connector
Connector: D-sub 9-pin (female, inch-standard)
RS-232C connector
Connector: D-sub 9-pin (female, inch-standard)
PARALLEL connector
Connector: D-sub 25-pin (female, inch-standard)
Timecode INPUT connector
Connector: XLR-3-31
Signal voltage amplitude: 0.5–10 Vp-p
Input impedance: 10 kΩ
Format: SMPTE 12M-1999 compliant
Timecode OUTPUT connector
Connector: XLR-3-32
Signal voltage amplitude: 2 Vp-p
Output impedance: 100 Ω
Format: SMPTE 12M-1999 compliant
WORD/VIDEO IN connector
Connector: BNC
Input voltage: 5V TTL equivalent (WORD IN)
Signal voltage amplitude: 1 Vp-p (VIDEO IN)
Input impedance: 75 Ω ±10%
Allowable frequency deviation of external
synchronization: ± 100 ppm
Includes switch for enabling termination
Input frequency (WORD):
44.1/47.952/48/48.048/88.2/96/176.4/192kHz
(47.952/48.048: 48 kHz ±0.1% pull-down/pull-up)
Input signal (VIDEO):
24/25/29.97/30 Frame
(NTSC/PAL Black burst, HDTV Tri-Level)
WORD/VIDEO THRU/OUT connector
Connector: BNC
Signal voltage amplitude: 5V TTL equivalent
Output impedance 75 Ω ±10%
Output frequency (WORD):
44.1/47.952/48/48.048/88.2/96/176.4/192kHz
(47.952/48.048: 48kHz±0.1% pull-down/pull-up)
Frequency stability: ±10 ppm or less (Ta = 20º C)
OUT/THRU switch included
(OUT is only for WORD OUT)
ETHERNET connector
Connector: RJ45
Supported standards: 100BASE-TX, 1000BASE-T
KEYBOARD connector
Connector: Mini-DIN (PS/2)
USB connector
Connector: USB A-type 4-pin
Protocol: USB 2.0 HIGH SPEED (480 Mbps)
REMOTE connector
Connector: etherCON (CAT6 compatible)
Power supply voltage: 13 V/41 V
Signal: LVDS serial