Extron Electronics MAV Plus series Large Scale User Guide - Manual (Page 109)

4-21 CrossPoint 450 Plus and MAV Plus Switchers • Programmer’s Guide
Command/Response Table for IP-Specific SIS Commands
Symbol definitions
X3)
= Matrix name (Up to 240 characters)
N The following characters are invalid in the name: {space} ~ , @ = ` [ ] { } < > ‘ “ ; : \ | and ?.
X3!
= Default name Factory default name (model name + last 3 pairs of MAC address)
X3@
= Time and date (set) In the format: MM/DD/YY•HH:MM:SS where:
MM = month: 01 (January) through 12 (December)
DD = day: 01 – 31
YY = year: 00 – 99
HH = hour: 00 – 24
MM = minutes: 00 – 59
SS = seconds: 00 – 59
X3#
= Time and date (read) In the format: Day,•DD•Mmm•YYYY•HH:MM:SS where
Day = weekday: Mon – Sun
DD = day: 01 – 31
Mmm = month: Jan – Dec
YYYY = year: 2000 – 2099
HH = hour: 00 – 24
MM = minutes: 00 – 59
SS = seconds: 00 – 59
X3$
= GMT offset -12.0 through +14.0 (hours and minutes removed from GMT)
X3%
= Daylight Saving Time 0 = Daylight Saving Time off/ignore
1 = Daylight Saving Time on (northern hemisphere)
2 = Daylight Saving Time on (Europe)
3 = Daylight Saving Time on (Brazil)
X3^
= IP address ###-###-###-###
X3&
= Hardware (MAC) address ##-##-##-##-##-##
X3*
= Number of open connections 0 – 255
X3(
= Password 12 alphanumeric characters
N The following characters are invalid in passwords: {space} ~ , @ = ` [ ] { } < > ‘ “ ; : \ | and ?.
X4)
= Domain name Standard domain name conventions apply (for example, xxx.com)
N The following characters are invalid in passwords: {space} ~ , = ` [ ] { } < > ‘ “ ; : \ | and ?.
The @ character is only acceptable as the lead-in to the domain name (such as @extron.com).
X4!
= E-mail account 65 – 72. 65 = e-mail recipient #1, 66 = 2, 67 = 3, ... , 72 = recipient #8.
X4@
= E-mail address Typical e-mail address format (for example: [email protected])
X4#
- Notify when? 0 = No response, 1 = fail/missing, 2 = fixed/restored, 3 = both 1 and 2
X4$
= Notification selections 01 – 64 = input numbers
98 = power supplies
99 = fans
X4%
= Notify status (for read) 66-digit number. For each digit: 0 = do not notify, 1 = notify.
X4^
= DHCP 0 = off, 1 = on
X4&
= Port # 01 = rear panel Remote port, 02 = front panel Configuration port)
X4*
= Baud rate 9600, 19200, 38400, 115200
X4(
= Parity O dd, even, none, mark, space (only first letter required)
X5)
= Data bits 7, 8
X5!
= Stop bits 1, 2
X5@
= Port type 0 = RS-232, 1 = RS-422
X5#
= Verbose mode 0 = Clear/none (default for Telnet connection
1 = Verbose mode (default for RS-232 / RS-422 connection)
2 = Tagged responses for queries
3 = Verbose mode and tagged for queries
N If tagged responses is enabled, all read commands return the constant string and the value as the set command does (for example, the read
matrix name command,
E
CN
}
, returns IPN •
X3)]
).
X5$
= Security level 00 = Anonymous 11 = User
10 = Extended security levels 1 through 10 12 = Administrator
X5%
= Port timeout interval (in 10-sec. increments) 1 (= 10 seconds) – 65000 (default is 30 = 300 seconds = 5 minutes)