Yaskawa CM092 - Manual (Page 69)

Product Codes & Parameter Tables 5-12
‹ Class 6Bh, Instance 1 - Motor Object (Continued)
‹ Class 6Ch, Instance 1 - Option Object
FX-XX parameters all share the same service (GET/SET), data type (Word) and number of bytes (2)
Parameter Name
Attribute [hex]
F7U G7U P7U E7U G5M
E3-03 Motor 2 Maximum Voltage VAC 28 (1Ch) 28 (1Ch)
E3-04 Motor 2 Base Frequency Hz 29 (1Dh) 29 (1Dh)
E3-05 Motor 2 Mid Frequency Hz 30 (1Eh) 30 (1Eh)
E3-06 Motor 2 Mid Voltage VAC 31 (1Fh) 31 (1Fh)
E3-07 Motor 2 Minimum Frequency 32 (20h) 32 (20h)
E3-08 Motor 2 Minimum Voltage VAC 33 (21h) 33 (21h)
E4-01 Motor 2 Maximum Frequency Hz 34 (22h) 34 (22h) 25 (19h)
E4-02 Motor 2 Maximum Voltage VAC 35 (23h) 35 (23h) 26 (1Ah)
E4-03 Motor 2 Base Frequency 36 (24h) 36 (24h) 27 (1Bh)
E4-04 Motor 2 Mid Frequency 37 (25h) 37 (25h) 28 (1Ch)
E4-05 Motor 2 Mid Voltage 38 (26h) 38 (26h) 29 (1Dh)
E4-06 Motor 2 Minimum Frequency 39 (27h) 39 (27h) 30 (1Eh)
E4-07 Motor 2 Minimum Voltage 40 (28h) 40 (28h) 31 (1Fh)
E4-08 Motor 2 Slip Compensation Gain Motor 2 63 (3Fh)
E4-09 Motor 2 ASR P Gain Motor 2 64 (40h)
E4-10 Motor 2 ASR I Time Motor 2 Sec 65 (41h)
E4-11 Motor 2 Torque Compensation Gain Motor 2 66 (42h)
E5-01 Motor 2 Rated FLA 32 (20h)
E5-02 Motor 2 Rated Slip Hz 33 (21h)
E5-03 Motor 2 No Load Current A 34 (22h)
E5-04 Motor 2 Number of Poles 35 (23h)
E5-05 Motor 2 Terminal Resistance Ohm 36 (24h)
E5-06 Motor 2 Leakage Inductance % 37 (25h)
Parameter Name
Attribute [hex]
F7U G7U P7U E7U G5M
F1-01 PG Pulses/Revolution 1 1 1
F1-02 PG Feedback Loss Selection 2 2 2
F1-03 PG Overspeed Selection 3 3 3
F1-04 PG Deviation Selection 4 4 4
F1-05 PG Rotation Selection 5 5 5
F1-06 PG Output Ratio 6 6 6
F1-07 PG Ramp PI/I Selection 7 7 7
F1-08 PG Overspeed Level % 8 8 8
F1-09 PG Overspeed Time Sec 9 9 9
F1-10 PG Deviation Level % 10 (0Ah) 10 (0Ah) 10 (0Ah)
F1-11 PG Deviation Time Sec 11 (0Bh) 11 (0Bh) 11 (0Bh)
F1-12 PG Gear Teeth 1 12 (0Ch) 12 (0Ch) 12 (0Ch)
F1-13 PG Gear Teeth 2 13 (0Dh) 13 (0Dh) 13 (0Dh)