Roland Fantom-X7 - Manual (Page 171)

171
Recording Songs
If you want the tempo to change during the song, you can record
those tempo changes in the Tempo track. If tempo changes have
already been recorded in the tempo track, they will be rewritten.
Set the following recording parameters in addition to the basic
settings described in step 3 of
“Basic Operation for Realtime
Recording” (p. 170).
Tempo Rec Sw (Tempo Recording Switch)
Specify whether tempo changes will be recorded (ON), or not (OFF).
Value: OFF, ON
You will be able to use realtime control knob ([ ])
movements to control the tempo easily (p. 140).
You can record repeatedly over a specified area (Loop recording), or
re-record just that area (Punch-in recording).
Set the following recording parameters in addition to the basic
settings described in step 3 of
“Basic Operation for Realtime
Recording” (p. 142).
Loop/Punch
Specify how loop recording or punch-in recording is to take place.
Value
OFF: Loop recording or punch-in recording will
not occur.
LOOP (POINT): Recording takes place repeatedly, according
to the loop point settings.
LOOP (1 MEAS): The one-measure area starting at the record-
start measure will be recorded repeatedly.
LOOP (2 MEAS): The two-measure area starting at the record-
start measure will be recorded repeatedly.
LOOP (4 MEAS): The four-measure area starting at the record-
start measure will be recorded repeatedly.
LOOP (8 MEAS): The eight-measure area starting at the record-
start measure will be recorded repeatedly.
LOOP (16 MEAS): The sixteen-measure area starting at the record-
start measure will be recorded repeatedly.
LOOP SONG ALL: The entire song from beginning to end will
be recorded repeatedly.
AUTO PUNCH: Auto punch-in recording will be performed.
You must pre-specify the area (punch points)
in which recording is to take place. This is
convenient when you want to re-record over a
mistake. The song will play back when you
begin recording. When you reach the punch-
in point, playback will switch to record mode.
MANUAL PUNCH: Manual punch-in recording will be performed.
Recording takes place (erasing the existing
data) in the area that you specify by pressing a
pedal or button. This is convenient when you
want to re-record more than one location in
which you made a mistake. The song will play
back when you begin recording. When you
press a pedal or button, playback will switch to
record mode, and will switch back to play
mode when you press the pedal or button once
again. By pressing the pedal or button, you can
toggle between record and play modes.
Start Point
Specify the measure and beat at which loop recording or auto punch-
in recording is to begin. It is not possible to specify the Tick.
End Point
Specify the measure and beat at which loop recording or auto punch-
in recording is to Stop. It is not possible to specify the Tick.
The minimum loop length is four quarter notes.
Using Auto Punch-In Recording
1. In the Realtime Rec Standby window, set the Loop/Punch
parameter to “AUTO PUNCH.”
2. Set the Start Point/End Point parameters to the desired
punch points.
3. Move to a measure earlier than the specified Start Point,
and press [PLAY].
The song will begin playing. Recording will begin at the
location specified by the Start Point parameter. Playback will
resume at the location specified by the End Point parameter.
4. Press [STOP] to stop playback.
Using Manual Punch-In Recording
If you want to use a pedal connected to the PEDAL CONTROL
jack to specify the area for recording, you must first set the
Pedal 1 or 2 Assign parameter to “PUNCH I/O” (p. 226).
1. In the Realtime Rec Standby window, set the Loop/Punch
parameter to “MANUAL PUNCH.”
2. Press [PLAY].
Song playback will begin, and the Realtime Recording window
will appear.
fig.18-004_50
3. At the point where you want to begin recording, press [F5
(Punch In)] or step on the pedal.
Playback will switch to record mode.
4. At the point where you want to stop recording, once again
press [F5 (PUNCH OUT)] or step on the pedal.
You will return to playback mode.
5. Press [STOP] to stop playback.
Recording Tempo Changes in a
Song (Tempo Recording)
Loop Recording and Punch-In
Recording
Fantom-X678_r_e.book 171 ページ ２００５年５月１２日 木曜日 午後４時４０分