Roland Fantom-X7 - Manual (Page 289)

289
Effects List
65: GATED REVERB
This is a special type of reverb in which the reverberant sound is cut
off before its natural length.
fig.MFX-65
66: OVERDRIVE → CHORUS
fig.MFX-66
67: OVERDRIVE → FLANGER
fig.MFX-67
Parameter Value Description
Type ROOM1,
ROOM2,
STAGE1,
STAGE2,
HALL1, HALL2 Type of reverb
ROOM1: dense reverb with
short decay
ROOM2: sparse reverb with
short decay
STAGE1: reverb with greater
late reverberation
STAGE2: reverb with strong
early reflections
HALL1: reverb with clear rever-
berance
HALL2: reverb with rich rever-
berance
Pre Delay 0.0–100.0 ms Adjusts the delay time from the di-
rect sound until the reverb sound
is heard.
Time # 0–127 Time length of reverberation
HF Damp 200–8000 Hz,
BYPASS Adjusts the frequency above
which the reverberant sound will
be cut.
As the frequency is set lower,
more of the high frequencies
will be cut, resulting in a softer
and more muted reverberance.
If you do not want to cut the
high frequencies, set this pa-
rameter to BYPASS.
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Balance # D100:0W–
D0:100W Volume balance between the direct
sound (D) and the reverb sound
(W)
Level 0–127 Output Level
Parameter Value Description
Type NORMAL, REVERSE,
SWEEP1, SWEEP2 Type of reverb
NORMAL: conventional
gated reverb
REVERSE: backwards re-
verb
SWEEP1: the reverberant
sound moves from right to
left
SWEEP2: the reverberant
sound moves from left to
right
Pre Delay 0.0–100.0 ms Adjusts the delay time from
the direct sound until the re-
verb sound is heard.
Gate Time 5–500 ms Adjusts the time from when
the reverb is heard until it
disappears.
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Balance # D100:0W–D0:100W Volume balance between the
direct sound (D) and the re-
verb sound (W)
Level # 0–127 Output Level
L in
R in
L out
R out
Gated Reverb
2-Band
EQ
Balance W
Balance W
Balance D
Balance D
2-Band
EQ
Parameter Value Description
Overdrive
Drive # 0–127 Degree of distortion
Also changes the volume.
Overdrive
Pan # L64–63R Stereo location of the overdrive
sound
Chorus Pre
Delay 0.0–100.0 ms Adjusts the delay time from the
direct sound until the chorus
sound is heard.
Chorus Rate # 0.05–10.00 Hz, note Frequency of modulation
Chorus Depth 0–127 Depth of modulation
Chorus
Balance # D100:0W–D0:100W Adjusts the volume balance be-
tween the sound that is sent
through the chorus (W) and the
sound that is not sent through
the chorus (D).
Level 0–127 Output Level
Parameter Value Description
Overdrive
Drive # 0–127 Degree of distortion
Also changes the volume.
Overdrive
Pan # L64–63R Stereo location of the overdrive
sound
Flanger Pre
Delay 0.0–100.0 ms Adjusts the delay time from
when the direct sound begins
until the flanger sound is heard.
Flanger Rate # 0.05–10.00 Hz, note Frequency of modulation
Flanger Depth 0–127 Depth of modulation
Flanger
Feedback # -98– +98 % Adjusts the proportion of the
flanger sound that is fed back
into the effect. Negative (-) set-
tings will invert the phase.
Flanger
Balance # D100:0W–D0:100W Adjusts the volume balance be-
tween the sound that is sent
through the flanger (W) and the
sound that is not sent through
the flanger (D).
Level 0–127 Output Level
L in
R in
Chorus Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
L in
R in
Flanger Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
Fantom-X678_r_e.book 289 ページ ２００５年５月１２日 木曜日 午後４時４０分