Roland Fantom-X7 - Manual (Page 293)

293
Effects List
note:
fig.MFX-note2.e_88
The Fantom-X’s Chorus effect unit can also be used as a stereo delay
unit.
These settings allow you to select chorus or delay, and the
characteristics of the selected effect type.
note:
fig.MFX-note2.e
About the STEP RESET function
06: STEP FILTER
16: STEP RING MODULATOR
19: STEP PAN
20: SLICER
63: STEP PITCH SHIFTER
The above five types contain a sixteen-step sequencer.
For these types, you can use a multi-effect control to reset the
sequence to play from the first step.
To do this, set the multi-effect control Destination to “Step
Reset.”
For example if you are using the modulation lever to control the
effect, you would make the following settings.
Source: CC01: MODULATION
Destination: Step Reset
Sens: +63
With these settings, the sequence will play back from the first
step whenever you operate the modulation lever.
(Double note) (Dotted whole note),
(Dotted half note),
(Dotted thirty-second note),
(Whole note),
(Double-note triplet),
(Sixteenth-note triplet), (Thirty-second note),
(Sixty-fourth-note triplet), (Sixty-fourth note), (Thirty-second-note triplet),
(Dotted eighth note), (Quarter-note triplet), (Eighth note),
(Half-note triplet), (Quarter note), (Dotted quarter note),
(Whole-note triplet),
(Half note),
(Sixteenth note), (Eighth-note triplet), (Dotted sixteenth note),
Chorus Parameters
Parameter Value Description
Chorus
Type 0 (OFF),
1 (CHORUS),
2 (DELAY),
3 (GM2 CHORUS) Selects either Chorus or Delay.
0 (OFF): Neither Chorus or Delay
is used.
1 (CHORUS): Chorus is used.
2 (DELAY): Delay is used.
3 (GM2 CHORUS): GM2 Chorus
is used.
Type: 1 (CHORUS)
Rate 0.05–10.00 Hz, note Frequency of modulation
Depth 0–127 Depth of modulation
Pre Delay 0.0–100.0 ms Adjusts the delay time from the direct
sound until the chorus sound is heard.
Feedback 0–127 Adjusts the amount of the chorus
sound that is fed back into the effect.
Filter Type OFF, LPF, HPF Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff Freq
HPF: cuts the frequency range
below the Cutoff Freq
Cutoff Freq 200–8000 Hz Basic frequency of the filter
Phase 0–180˚ Spatial spread of the sound
Type: 2 (DELAY)
Delay Left 0–1000 ms, note Adjusts the delay time from the di-
rect sound until the delay sound is
heard.
Delay Right
Delay Center
Center
Feedback
-98–+98 % Adjusts the proportion of the delay
sound that is fed back into the ef-
fect. Negative (-) settings will invert
the phase.
HF Damp 200–8000 Hz,
BYPASS Adjusts the frequency above which
sound fed back to the effect will be
cut. If you do not want to cut the
high frequencies, set this parameter
to BYPASS.
Left Level 0–127 Volume of each delay sound
Right Level
Center Level
Type: 3 (GM2 CHORUS)
Pre-LPF 0–7 Cuts the high frequency range of
the sound coming into the chorus.
Higher values will cut more of
the high frequencies.
Level 0–127 Volume of the chorus sound
Feedback 0–127 Adjusts the amount of the chorus
sound that is fed back into the effect.
Delay 0–127 Adjusts the delay time from the di-
rect sound until the chorus sound is
heard.
Rate 0–127 Frequency of modulation
Depth 0–127 Depth of modulation
Send Level
To Reverb 0–127 Adjusts the amount of chorus sound
that will be sent to the reverb.
(Double note) (Dotted whole note),
(Dotted half note),
(Dotted thirty-second note),
(Whole note),
(Double-note triplet),
(Sixteenth-note triplet), (Thirty-second note),
(Sixty-fourth-note triplet), (Sixty-fourth note), (Thirty-second-note triplet),
(Dotted eighth note), (Quarter-note triplet), (Eighth note),
(Half-note triplet), (Quarter note), (Dotted quarter note),
(Whole-note triplet),
(Half note),
(Sixteenth note), (Eighth-note triplet), (Dotted sixteenth note),
Fantom-X678_r_e.book 293 ページ ２００５年５月１２日 木曜日 午後４時４０分