Roland Fantom-X7 - Manual (Page 272)

272
Effects List
05: SUPER FILTER
This is a filter with an extremely sharp slope. The cutoff frequency
can be varied cyclically.
fig.MFX-05
06: STEP FILTER
This is a filter whose cutoff frequency can be modulated in steps.
You can specify the pattern by which the cutoff frequency will
change.
fig.MFX-06
07: ENHANCER
Controls the overtone structure of the high frequencies, adding
sparkle and tightness to the sound.
fig.MFX-07
Parameter Value Description
Filter Type LPF, BPF,
HPF, NOTCH Filter type
Frequency range that will pass
through each filter
LPF : frequencies below the cutoff
BPF: frequencies in the region of the
cutoff
HPF: frequencies above the cutoff
NOTCH: frequencies other than the
region of the cutoff
Filter Slope -12, -24, -36 dB Amount of attenuation per octave
-36 dB: extremely steep
-24 dB: steep
-12 dB: gentle
Filter
Cutoff # 0–127 Cutoff frequency of the filter
Increasing this value will raise the
cutoff frequency.
Filter
Resonance # 0–127 Filter resonance level
Increasing this value will emphasize
the region near the cutoff frequency.
Filter Gain 0– +12 dB Amount of boost for the filter output
Modulation
Sw OFF,ON On/off switch for cyclic change
Modulation
Wave TRI, SQR,
SIN, SAW1,
SAW2 How the cutoff frequency will be mod-
ulated
TRI: triangle wave
SQR: square wave
SIN: sine wave
SAW1: sawtooth wave (upward)
SAW2: sawtooth wave (downward)
Rate # 0.05–10.00 Hz,
note Rate of modulation
Depth 0–127 Depth of modulation
Attack # 0–127 Speed at which the cutoff frequency
will change
This is effective if Modulation Wave
is SQR, SAW1, or SAW2.
Level 0–127 Output level
L in
R in
L out
R out
Super Filter
Super Filter
SAW1 SAW2
Parameter Value Description
Step 01–16 0–127 Cutoff frequency at each step
Rate # 0.05–10.00 Hz,
note Rate of modulation
Attack # 0–127 Speed at which the cutoff frequency
changes between steps
Filter Type LPF, BPF,
HPF, NOTCH Filter type
Frequency range that will pass
through each filter
LPF: frequencies below the cutoff
BPF: frequencies in the region of the
cutoff
HPF: frequencies above the cutoff
NOTCH: frequencies other than the
region of the cutoff
Filter Slope -12, -24, -36 dB Amount of attenuation per octave
-12 dB: gentle
-24 dB: steep
-36 dB: extremely steep
Filter
Resonance # 0–127 Filter resonance level
Increasing this value will emphasize
the region near the cutoff frequency.
Filter Gain 0– +12 dB Amount of boost for the filter output
Level 0–127 Output level
Parameter Value Description
Sens # 0–127 Sensitivity of the enhancer
Mix # 0–127 Level of the overtones gen-
erated by the enhancer
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Level 0–127 Output Level
L in
R in
L out
R out
Step Filter
Step Filter
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
2-Band
EQ
2-Band
EQ
Fantom-X678_r_e.book 272 ページ ２００５年５月１２日 木曜日 午後４時４０分