Output settings (output), 95 creating a rhythm set – Roland Fantom-X7 User Manual
Page 95
95
Creating a Rhythm Set
A-Env Level 1–3 (TVA Envelope Level 1–3)
Specify the TVA envelope levels (Level 1–Level 3). These settings
specify how the volume will change at each point, relative to the
standard volume (the Rhythm Tone Level value specified in the TVA
screen).
Value:
0–127
fig.06-041.e
fig.07-014_50
For details on these settings, refer to
Rhythm Out Assign
Specifies for each rhythm set how the direct sound will be output.
Value:
MFX:
Output in stereo through multi-effects. You can also
apply chorus or reverb to the sound that passes
through multi-effects.
A, B:
Output to the OUTPUT A (MIX) jack or OUTPUT B
jack in stereo without passing through multi-effects.
1–4:
Output to the INDIVIDUAL 1–4 jacks in mono
without passing through multi-effects.
If you've made settings so that sounds are separately routed to
the INDIVIDUAL 1 jack and INDIVIDUAL 2 jack, but no plug
is actually inserted in the INDIVIDUAL 2 jack, the sounds
routed to INDIVIDUAL 1 and INDIVIDUAL 2 will be mixed
and output from the INDIVIDUAL 1 jack.
If the Mix/Parallel parameter is set to “MIX,” all sounds are
output from the OUTPUT A (MIX) jacks in stereo (p. 230).
Tone Out Assign
Specifies how the direct sound of each tone will be output.
Value:
MFX:
Output in stereo through multi-effects. You can also
apply chorus or reverb to the sound that passes
through multi-effects.
A, B:
Output to the OUTPUT A (MIX) jack or OUTPUT B
jack in stereo without passing through multi-effects.
1–4:
Output to the INDIVIDUAL 1–4 jacks in mono
without passing through multi-effects.
If the Rhythm Output Assign is set to anything other than
“TONE,” these settings will be ignored.
If you've made settings so that sounds are separately routed to
the INDIVIDUAL 1 jack and INDIVIDUAL 2 jack, but no plug
is actually inserted in the INDIVIDUAL 2 jack, the sounds
routed to INDIVIDUAL 1 and INDIVIDUAL 2 will be mixed
and output from the INDIVIDUAL 1 jack.
*
If the Mix/Parallel parameter is set to “MIX,” all sounds are output
from the OUTPUT A (MIX) jacks in stereo (p. 230).
*
If you've set Tone Out Assign to “MFX,” set the MFX Output
Assign parameter (p. 208) to specify the output destination of the
sound that has passed through the multi-effects.
*
Chorus and reverb are output in mono at all times.
*
The output destination of the signal after passing through the chorus
is set with the Chorus Output Select (p. 209) and the Chorus Output
Assign (p. 209).
*
The output destination of the signal after passing through the reverb is
set with the Reverb Output Assign (p. 212).
Tone Out Level
Set the level of the signal that is sent to the output destination
specified by Patch/Tone Output Assign.
Value:
0–127
Tone Chorus Send (Send Level (Output=MFX))
Specifies the level of the signal sent to the chorus for each tone if the
tone is sent through MFX.
Value:
0–127
Tone Reverb Send (Send Level (Output=MFX))
Specifies the level of the signal sent to the reverb for each tone if the
tone is sent through MFX.
Value:
0–127
Output Settings (Output)
3
T1 T2
T3
T4
L3
L1
L2
Note off
Level
Time
Note on
T: Time L: Level
1
2
Fantom-X678_r_e.book 95 ページ ２００５年５月１２日 木曜日 午後４時４０分