FARGO electronic DTC300 - Manual (Page 444)

RESTRICTED USE ONLY Fargo Electronics, Inc.
DTC400/DTC300/DTC300M Card Printer Service Manual (Rev. 1.3) 16-3
Image Placement option, 6-107
image placement problems, 5-51
Image Placement value, 6-107
Image Position controls, 6-46
inches or mm option, 6-9
incorrect image darkness problems, 5-44
increase Printhead heat, 6-106
Input, 15-10
Input Feed Motor Assembly (E000806), 8-67, 8-68
Input Feed Roller (D900049), 8-67
Input Hopper, 15-10
Integrator-specific SecureMark media, 3-2
Interface, 2-4
Intermediate Transfer Media (InTM), 15-10
internal Printer settings, 6-45
ISO, 15-10
ISO 7811-2 Magnetic Stripe, 6-60
ISO encoded data format, 6-53
ISO Standard selections, 6-58
ISO Standard settings, 6-51
ISO Track Locations, 6-60
ITS-EMC, 2-2
ITS-EMC, 2-2
J
JIS II (Japanese Industrial Standard), 15-10
K
K Panel, 15-10
K Panel Resin options, 6-76, 6-100
K Panel Resin tab, 6-90
L
Lamination, 15-10
Lamination Drive, 10-2
Lamination Drive Stepper, 10-2
Lamination Roller Lift, 10-2
Lamination Sensor Calibration, 5-55
LAN (Local Area Network), 15-10
Landscape, 15-11
Landscape orientation, 6-46
LCD (Liquid Crystal Display), 15-11
LED (Light Emitting Diode), 15-11
less heat / more heat, 6-33, 6-34, 6-35, 6-42, 6-43
LoCo (Low Coercivity), 15-11
LPT Port (Line Printer Port), 15-11
LRC Generation, 6-58
LRC Generation Mode, 6-58
M
magnetic data, 6-113
Magnetic Encoder, 5-18
Magnetic encoding, 15-11
Magnetic Head Assembly Replacement, 8-75
Magnetic Offset option, 6-113
Magnetic Offset value, 6-113
Magnetic stripe, 15-11
Magnetic Stripe Encoding Module, 6-50
Magnetic Stripe reader, 5-15
Magnetic Track, 15-11
Magnetic Track Options, 6-51
Magnetic Track Selection, 6-51, 6-52
Magnetic Track Selection option, 6-51
Magnetic Verify, 15-11
maximum adjustment range, 6-108, 6-113
MB (Megabyte), 15-12
Media, 15-11
Memory, 2-4, 15-12
Menu, 15-12
Metallic Resin, 2-11
Monitor, 6-21
Monochrome, 15-12
Monochrome Dye-Sub (B), 5-55
Monochrome Resin (K), 5-55
Motor Voltages (when active), 10-2
Multi-Language Extension (MLE), 6-56
N
Network, 15-12
None, 6-21
O
Oersted (Oe), 15-12
Offset, 15-12
Omit Signature Area setting, 6-73
On LED, 5-54, 5-56
on-line Media ordering, 3-1
on-line Media ordering system, 3-1
onscreen card design, 6-96
Operating Temperature, 2-4
optional Magnetic Stripe Encoding Module, 6-50
O-Ring, 15-12
OS (Operating System), 15-12
Output, 15-12
Output Hopper, 15-12
Overlaminate, 15-13
Overlay, 15-12
Overlay / Print Area, 6-73, 6-74
Overlay / Print Area options, 6-70
Overlay / Print Area tab, 6-64
Oversized Cards, 15-13
P
Parallel, 15-13
Parallel port, 15-13
Parts Replacement, 8-1
Password protection, 3-1
Pause button and LED, 2-9
Pause/Resume button, 5-54, 5-56
PC (Personal Computer), 15-13
PCB (Printed Circuit Board), 15-13
Peel, 15-13
Peel-Off, 15-13
Peripheral, 15-13
PET, 15-14
Photo, 6-22, 6-32