Setting up the network (clx-3175n only), Supported operating environments, Configuring network protocol via the machine – Samsung CLX-3175FN User Manual

Page 122: Using the setip program, Setting up the network

Advertising
background image

25 _

Getting started

SETTING UP THE NETWORK (CLX-3175N ONLY)

You need to set up the network protocols on the machine to use it in the

network environment. You can set up the basic network settings through the

machine's control panel.

Supported operating environments

The following table shows the network environments supported by the

machine:

Configuring network protocol via the machine

You can set up TCP/IP network parameters, follow the steps listed below.
1.

Make sure your machine is connected to the network with an RJ-45

Ethernet cable.

2.

Make sure you have turned on the machine.

3.

Press Menu and then OK.

4.

Press the left/right arrow until Network appears and press OK.

5.

Press the left/right arrow until TCP/IP appears and press OK.

6.

Press the left/right arrow until Static appears and press OK.

7.

Press the left/right arrow until IP Address appears and press OK.
Enter a byte between 0 and 255 using the left/right arrow and press OK.

Repeat this to complete the address from the 1st byte to the 4th byte.

8.

Repeat steps 7 to configure the other TCP/IP parameters: subnet mask

and gateway address.

9.

Press Stop/Clear to return to ready mode.

Using the SetIP program

This program is for the network IP setting using the MAC address which is

the hardware serial number of the network printer card or interface.

Especially, it helps the network administrator set several network IPs at the
same time.

Installing the program

1.

Insert the driver CD provided along with your machine. When the driver

CD runs automatically, close the window.

2.

Start Windows Explorer and open the X drive. (X represents your CD-

ROM drive.)

3.

Double-click Application > SetIP.

4.

Double-click Setup.exe to install this program.

5.

Click OK.

If necessary, select a language from the drop-down list.

6.

Follow the instructions in the window and complete the installation.

Setting network values

1.

Print the machine’s network configuration report to find your machine’s

MAC address. See "Printing reports" on page 44.

2.

From the Windows Start menu, select All Programs > Samsung
Network Printer Utilities

> SetIP > SetIP.

3.

Click

to open the TCP/IP configuration window.

4.

Enter the network card's MAC address, IP address, subnet mask,
default gateway, and then click Apply.

5.

Click OK, then the machine prints the network information. Confirm the

settings are correct.

6.

Click Exit.

ITEM

REQUIREMENTS

Network interface

Ethernet 10/100 Base-TX

Network operating system

Windows 2000/XP/2003/2008/Vista/7/

Server 2008 R2

Various Linux OS

MAC OS 10.3 ~ 10.6

Network protocols

TCP/IP

Standard TCP/IP

LPR

IPP/HTTP

Bonjour

DHCP

BOOTP

If you are in a non-static IP address environment and need to setup a

DHCP network protocol, go to the

http://developer.apple.com/

networking/bonjour/download/

, select the program Bonjour for

Windows due to your computer operating system, and install the

program. This program will allow you to fix the network parameter

automatically. Follow the instruction in the installation window. This
Bonjour program does not support Linux.

Contact the network administrator if you are not sure how to configure.

You can also set up the network settings through the network

administration programs.

SyncThru™ Web Admin Service

: Web-based printer

management solution for network administrators. SyncThru™
Web Admin Service

provides you with an efficient way of

managing network devices and lets you remotely monitor and

troubleshoot network machines from any site with corporate
internet access. Download this program from

http://

solution.samsungprinter.com

.

SyncThru™ Web Service

: Web server embedded on your

network print server, which allows you to:

- Configure the network parameters necessary for the machine to

connect to various network environments.

- Customize machine settings.

SetIP

: Utility program allowing you to select a network interface

and manually configure the IP addresses for use with the TCP/IP

protocol. (See "Using the SetIP program" on page 25.)

You can only use SetIP program when your machine is connected

to a network.

The following procedure is based on windows XP. If you use

Macintosh or Linux OS, see Software section

when you enter the MAC address, enter it without colon(:).

Advertising
This manual is related to the following products: