KORG Triton Studio User Manual
Page 116
105
Sampling
P0
P1
P2
P3
P4
P5
P8
5
In “Curve,” specify the way in which the volume will
change.
Linear:
The volume will change linearly. For normal
fade-in or fade-out, select Linear.
Power:
The volume will change non-linearly. When you
use “Mix” (1–1F) to combine a faded-in waveform with a
different faded-out waveform (i.e., crossfade), using a
Linear
fade-in/out may produce an impression that the
volume has dropped in the middle of the curve. In such
cases, use Power to perform the fade-in/out.
6
In “Save to No.,” specify the save destination sample
number. By default, an unused sample number will be
selected.
The sample number cannot be specified if “Overwrite” is
checked (
For stereo samples, use “Save to No.(L)” and
“(R)” to specify the save-destination of the L and R chan-
nels.
7
To execute the Volume Ramp command, press the OK
button
. To cancel, press the Cancel button.
1–1K: Rate Convert
This command lowers the sampling rate (frequency) of the
sampled data by 2/3, 1/2, 1/3, 1/4, or 1/6. The sampling
frequency of input is fixed at 48 kHz, but you can use this
command to create “down-sampling” effects. The sample
data is thinned to convert it into sample data of a lower sam-
pling frequency.
The “Rate Convert” command is always executed on all
waveform data of the selected sample, regardless of the
“Edit Range Start” and “Edit Range End” settings.
1
Use “Sample Select” (1–1b) to select the sample that you
wish to edit.
2
Select “Rate Convert” to access the dialog box.
3
The sampling rate of the selected sample is shown at the
right of “Rate.” At the right of the “->” you can select the
desired amount of the sampling rate conversion: 2/3, 1/2,
1/3, 1/4 1/6
. The sampling rate following conversion will
be displayed in Hz.
4
In “Save to No.,” specify the save destination sample
number. By default, an unused sample number will be
selected.
The sample number cannot be specified if “Overwrite” is
checked (
For stereo samples, use “Save to No.(L)” and
“(R)” to specify the save-destination of the L and R chan-
nels.
5
To execute the Insert Zero command, press the OK but-
ton
. To cancel, press the Cancel button.
This command cannot be executed on a sample whose
sampling rate is 11.025 kHz or less.
Stereo samples must have the same sampling rate.
Although it is possible to select mono multisamples for
-L and -R and convert their sampling rate separately,
they can no longer be handled as a stereo sample in this
case.
1–1L: Reverse
This command reverses the sample data (i.e., exchanges the
beginning and end).
The “Reverse” command is always executed on all wave-
form data of the selected sample, regardless of the “Edit
Range Start” and “Edit Range End” settings.
1
Use “Sample Select” (1–1b) to select the sample that you
wish to edit.
2
Select “Reverse” to access the dialog box.
3
In “Save to No.,” specify the save destination sample
number. By default, an unused sample number will be
selected.
The sample number cannot be specified if “Overwrite” is
checked (
For stereo samples, use “Save to No.(L)” and
“(R)” to specify the save-destination of the L and R chan-
nels.
4
To execute the Reverse command, press the OK button.
To cancel, press the Cancel button.
When you execute this command, all of the sample data
will be rewritten to reverse its direction. The P2: Loop
Edit also contains a “Rev” (2–1c) command, which sim-
ply reverses the playback direction without affecting
the sample data itself.
1–1M: Grid
This command displays a grid in the “sample waveform dis-
play.”
When you set the Grid to On and execute this command,
vertical dotted lines will appear in the “sample waveform
display” according to the specified resolution (“Resolution”)
and tempo (“Grid” 1–1c, 2–1c). Use the grid when you wish
to cut the sample data or determine waveform starting loca-
tions based on BPM values or beats.
The vertical dotted lines will be shown starting at the
“Start” (when Loop is off) or “Loop Start” (when Loop
is on) (P2: Loop Edit) addresses, and are calculated
according to the playback when the sample is played by
the currently selected key (displayed in gray) (
☞“Key-
board & Index” 0–1a).
1
Use “Sample Select” (1–1b) to select a sample.
2
Select “Grid” to access the dialog box.
3
Use the On/Off Radio buttons to switch the grid on or
off.
0–1A
0–1B
0–1C
0–1D
0–1E
0–1G
0–1H
0–1I
0–1J
0–1F
1–1M
1–1N