KORG Triton Studio - Manual (Page 30)

Program
P0
P1
P2
P3
P4
P5
P7
P8
P9
19
Intensity to B (LFO1 AMS Int. to B) [–99…+99]
Specifies the depth and direction of the effect that “AMS
(LFO1 AMS)” will have on filter 1B (
☞“Intensity to A (LFO1
AMS Int. to A)”).
3–3b: LFO 2
Adjusts the depth of the cyclic modulation applied by OSC1
LFO2 (set by 5–2) to the cutoff frequency of filters 1A and 1B
(
☞LFO 1: 3–3a).
Intensity to A (LFO2 Int. to A) [–99…+99]
Intensity to B (LFO2 Int. to B) [–99…+99]
JS–Y Intensity to A (LFO2 JS–Y Int. to A) [–99…+99]
JS–Y Intensity to B (LFO2 JS–Y Int. to B) [–99…+99]
AMS (LFO2 AMS) [Off, (PEG, FEG, AEG, KT, EXT)]
Intensity to A (LFO2 AMS Int. to A) [–99…+99]
Intensity to B (LFO2 AMS Int. to B) [–99…+99]
▼ 3–3: Page Menu Command
☞0–1A: Write Program, 1–1A: Copy Oscillator, 1–1B: Swap
Oscillator
3–4: Filter1 EG
Here you can make settings for the EG that will produce
time-varying changes in the cutoff frequency of filters 1A
and 1B.
The depth of the effect that these settings will have on the
filter 1 cutoff frequency is determined by Filter EG (3–2b).
3–4a: Filter1 EG
Specifies the time-varying change produced by the filter 1
EG.
Level:
The result will depend on the filter that was selected in “Fil-
ter Type
” (3–1a). For example with the Low Pass Resonance
filter, positive (+) values of EG Intensity will cause the tone
to be brightened by positive (+) levels, and darkened by
negative (–) levels
.
Start (Start Level) [–99…+99]
Specifies the cutoff frequency at the time of note-on.
Attack (Attack Level) [–99…+99]
Specifies the cutoff frequency after the attack time has
elapsed.
Break (Break Point Level) [–99…+99]
Specifies the cutoff frequency after the decay time has
elapsed.
Sustain (Sustain Level) [–99…+99]
Specifies the cutoff frequency that will be maintained from
after the slope time has elapsed until note-off occurs.
Release (Release Level) [–99…+99]
Specifies the cutoff frequency that will occur when the
release time has elapsed.
Time:
These parameters specify the time over which each change
will occur.
Attack (Attack Time) [00…99]
Specifies the time over which the level will change from
note-on until the attack level is reached.
Decay (Decay Time) [00…99]
Specifies the time over which the level will change from the
attack level to the break point level.
Slope (Slope Time) [00…99]
Specifies the time over which the level will change after the
decay time has elapsed until the sustain level is reached.
Release (Release Time) [00…99]
Specifies the time over which the level will change after
note-on occurs until the release level is reached.
3–4b: Level Modulation
These settings let you use alternate modulation to control
the Level parameters of the filter 1 EG.
AMS (Level Mod. AMS) [Off, (KT, EXT)]
Selects the source that will control the Level parameters of
the filter 1 EG (“AMS List”
☞p.242).
Intensity (AMS Intensity) [–99…+99]
Specifies the depth and direction of the effect that “AMS
(Level Mod. AMS)” will have.
For example if “AMS (Level Mod. AMS)” is Velocity, and
you set “St (AMS SW Start),” “At (AMS SW Attack)” and
“Br (AMS SW Break)” to + and set “Intensity (AMS Inten-
sity)
” to a positive (+) value, the EG levels will rise as you
play more strongly. If “Intensity (AMS Intensity)” is set to a
negative (–) values
, the EG levels will fall as you play more
strongly.
With a setting of 0, the levels specified by “Filter 1 EG” (3–
4a) will be used.
St (AMS SW Start) [–, 0, +]
Specifies the direction in which “AMS (Level Mod. AMS)”
will affect “Start (Start Level).” When “Intensity (AMS
Intensity)” has a positive (+) value, a setting of + for this
parameter will allow “AMS (Level Mod. AMS)” to raise the
EG level, and a setting of – will allow “AMS (Level Mod.
AMS)” to lower the EG level. With a setting of 0 there will be
no change.
3–4
3–4a
3–4c 3–4b
Note-on
Note-off
Attack
Time
Start
Level
Decay
Time Release
Time
Release
Level
Attack Level
The specified
cutoff
frequency
Sustain Level
Time
Break
Point
Level
Slope
Time