KORG Triton Studio - Manual (Page 214)

Ef
fect
203
a: Control Mode, e: Voice1: Resonance, h: Voice2: Resonance
This parameter determines the resonance intensity.
When “Control Mode” = Manual, the “Resonance” parameter
sets the intensity of resonance. If the “Resonance” parameter has a
negative value, harmonics will be changed, and resonance will
occur at a pitch one octave lower.
When “Control Mode” = LFO, the intensity of resonance varies
according to the LFO. The LFO sways between positive and nega-
tive values, causing resonance to occur between specified pitches
an octave apart in turn.
When “Control Mode” = D-mod, the resonance is controlled by
the dynamic modulation source. If JS X or Ribbon is assigned as
the modulation source, the pitch an octave higher and lower can
be controlled, similar to when LFO is selected for Control Mode.
a: LFO/D-mod Invert
When “Control Mode” = LFO or D-mod, the controlled phase of
either Voice 1 or 2 will be reversed. When the resonance pitch is
set for Voice 1 (Resonance has a positive value), Voice 2 will reso-
nate at a pitch an octave below (Resonance has a negative value).
d: Voice1: Pitch, d: Fine [cent], g: Voice2: Pitch, g: Fine [cent]
The Pitch parameter specifies the pitch of resonance by note
name. The “Fine” parameter allows for fine adjustment in steps of
cents.
e: High Damp [%], h: High Damp [%]
This parameter sets the damping amount of resonant sound in the
high range. Lower values will make a metallic sound with a
higher range of harmonics.
030: Doppler
This effect simulates the “Doppler effect” of a moving sound
with a changing pitch, similar to the siren of an passing
ambulance. Mixing the effect sound with the dry sound will
create a unique chorus effect.
a: LFO Mode, a: Src, b: LFO Sync
The “LFO Mode” parameter switches LFO operation mode. When
Loop
is selected, the Doppler effect will be created repeatedly. If
“LFO Sync” is set to On, the LFO will be reset when the modula-
tion source specified with the “Src” parameter is turned on.
When “LFO Mode” is set to 1-Shot, the Doppler effect is created
only once when the modulation source specified in the “Src” field
is turned on. At this time if you do not set the “Src” parameter, the
Doppler effect will not be created, and no effect sound will be out-
put.
The effect is off when a value for the modulation source
specified for the “Src” parameter is smaller than 64, and the
effect is on when the value is 64 or higher. The Doppler
effect is triggered when the value changes from 63 or
smaller to 64 or higher.
e: Pitch Depth
With the Doppler effect, the pitch is raised when the sound
approaches, and the pitch is lowered when the sound goes away.
This parameter sets this pitch variation.
f: Pan Depth
This parameter sets the width of the stereo image of the effect
sound. With larger values, the sound seems to come and go from
much further away. With positive values, the sound moves from
left to right; with negative values, the sound moves from right to
left.
i
Voice2: Level
Sets the Voice2 output level 0...100
Pan
Sets the Voice2 stereo image L6...R6
j
Wet/Dry Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Src Off...Tempo
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance –100...+100
a
LFO Mode
Switches LFO operation mode Loop, 1-Shot
☞
,
Src Off...Tempo
When LFO Mode is set to 1-Shot, this modulation source triggers the
LFO
☞
b
LFO Sync Off, On
Switches between LFO reset on and off when LFO Mode is set to
Loop
☞
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Pan Depth
D -mod
+
Trigger LFO Mode = 1-Shot
Doppler
LFO
c
LFO Frequency [Hz] 0.02...20.00Hz
Sets the LFO speed
☞
Fx:009,
Src
Selects the modulation source of LFO speed Off...Tempo
Amt –20.00...+20.00Hz
Sets the modulation amount of LFO speed
d
BPM/MIDI Sync Off, On
Switches between using the frequency of the LFO speed and using
the tempo and notes
☞
Fx:009,
BPM
Selects MIDI Clock and assigns tempo MIDI, 40...240
☞
Fx:009
Base Note
Selects the type of notes that specify the LFO speed
☞
Fx:009
Times x1...x16
Sets the number of notes that specify the LFO speed
☞
Fx:009
e
Pitch Depth
Sets the pitch variation of the moving sound 0...100
☞
,
Src
Selects the modulation source of pitch variation Off...Tempo
Amt
Sets the modulation amount of pitch variation –100...+100
f
Pan Depth
Sets the panning of the moving sound –100...+100
☞
,
Src
Selects the modulation source of panning Off...Tempo
Amt
Sets the modulation amount of panning –100...+100
g
Wet/Dry Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Src Off...Tempo
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance –100...+100
Pitch
Higher
Doppler - Pitch / Pan Depth
Lower
Original Pitch
Left Center Right
Pitch Depth
Pan Depth
< < < < < <<<<<< >>>>>> > > > > >
Volume Louder Louder
Pan Depth
= (–) value Pan Depth
= (+) value