KORG Triton Studio - Manual (Page 192)

181
Ef
fect
If you want to play back an audio CD without applying
the TRITON STUDIO’s effects, set “Input” Analog set-
tings for Input1 to “Level” 127, “Pan” L000, “BUS
Select” L/R
, “Send1, 2” 000, and set Input2 “Pan” to
R127 and the remaining parameters to the same set-
tings as for Input1.
Use “BUS Select” (Global P0: 0–3a) to set Inputs 1/2 buses
by selecting from L/R, IFX1–5, 1–4, 1/2, 3/4, and Off.
“Send1 (to MFX1)” and “Send2 (to MFX2)” become effective
only when “BUS Select” (Global P0: 0–3a) is set to L/R or
Off
. If IFX1–5 is selected, use “Send1” and “Send2” for the
post-IFX signal ( ☞“3. Mixer”).
This setting is ignored in Sampling mode. Refer to “2–3.
Sampling Mode” for information on the Sampling
mode settings.
Insert effect settings are made in P8: Insert Effect of 1 Pro-
gram, 1 Combination, 1 Song, and Song Play modes. For the
external input sound from the various input jacks, you can
use the TRITON STUDIO’s effects as a 6-in 6-out effect pro-
cessor, or use them in conjunction with the internal sounds.
For example, in Program mode or Combination mode, you
can route the incoming signal from AUDIO INPUTs 1 and 2
and the oscillator sound to “Insert Effect 093: Vocoder” in
order to set up a vocoder effect in which the internal sound
is controlled by the mic inputs (“093: Vocoder”
☞p.233).
In Disk mode, the effects will have the settings of the
previously-selected mode.
3. Mixer
Use “Pan (CC#8),” “BUS Select,” “Send1,” and “Send2” of
the P8: “Insert FX” page for the post-IFX signal in all modes
to set the pan/bus and the send level to the Master Effects
MFX1 and MFX2.
If you have checked the “Chain” box to connect the Insert
Effects in series, these parameters “Pan (CC#8),” “BUS
Select,” “Send1” and “Send2” for the post-IFX (last Insert
Effect in the chain) signal become effective.
The master effects cannot be used in Sampling mode.
This means that here you can set only the “Pan” (CC#8)
that follows the insert effects.
3–1. Pan (CC#8)
This parameter enables you to set the pan of the post-IFX
signal.
If you are using the stereo-in/stereo-out Insert Effects
(
☞“In/Out”), set this parameter to “C064” to enable the
“Pan” settings for the oscillators (Program P4: 4–1b, 4–4),
timbres (Combination P0: 0–2b, P1: 1–1b), tracks (Sequencer
P0: 0–3a/4a, Song Play P0: 0–3a/4a), and audio inputs (Sam-
pling P0: 0–2a, Global P0: 0–3a).
If you are using mono-in/stereo–out or mono-in/mono–out
Insert Effects (
☞“In/Out”), the “Pan” settings for the oscil-
lators, timbres, tracks and audio inputs are ignored, and
they are set to Center. Use the “Pan (CC#8)” parameter (P8:
“Insert FX” page) to set the pan. “L000” is hard left, and
“R127” is hard right.
You can control these parameters via CC#8.
3–2. BUS Sel. (BUS Select)
This parameter enables you to specify the destination bus
for the post-IFX signals. “L/R” is a common setting to send
signals to the Master EQ before they are routed to the OUT-
PUT (MAIN) L/MONO and R outputs.
Select 1, 2, 3, 4, 1/2, or 3/4 to route the signals to OUTPUT
(INDIVIDUAL) 1, 2, 3, or 4 (
☞“Individual Outputs”). Select
“Off” so that no signals will be output to L/R, 1, 2, 3, or 4. In
this case, the signals are routed from the Master Effects to
AUDIO OUTPUT (MAIN). This setting is used when you
are connecting the Insert Effects with the Master Effects in
series using “Send1 (MFX1)” and “Send2 (MFX2).”
3–3. Send1, Send2
These parameters enable you to set the send level of the sig-
nals routed to Master Effects MFX1 and MFX2. These set-
tings are effective only when “BUS Select” is set to L/R or
Off
.
If you are not using any Insert Effects, use “Send1” and
“Send2” of the P8: “Routing” page in Program, Combina-
tion, Sequencer, and Song play modes to set the Master
Effect send level (Use the Global P0: Input/Sampling page
to set the send level for the audio inputs.).
“Send1” responds to CC#93 and “Send2” responds to
CC#91.
OSC1: Amp1 Pan=L000
OSC2: Amp2 Pan=R127
Left Center Right
Post IFX Pan(CC#8)
C064
Left Center Right
L032
L000
R096
R127
Insert Effect = Stereo In - Stereo Out
Left Center Right
Left Center Right
OSC1 OSC2
OSC1: Amp1 Pan=L032
OSC2: Amp2 Pan=R096
Post IFX Pan(CC#8)
C064
L032
L000
R096
R127
OSC1: Amp1 Pan=L000
OSC2: Amp2 Pan=R127
Left Center Right
Post IFX Pan(CC#8)
C064
Left Center Right
L032
L000
R096
R127
Insert Effect = Mono In - Stereo Out
OSC1 OSC2
Mono In - Mono Out