KORG Triton Studio - Manual (Page 234)

Ef
fect
223
070: Limiter – P4EQ
(Limiter – Parametric 4-Band EQ)
This effect combines a mono-type limiter and a four-band
parametric equalizer. You can change the order of the effect
connection.
071: Limiter – Cho/Flng
(Limiter – Chorus/Flanger)
This effect combines a mono-type limiter and a chorus/
flanger. You can change the order of the effect connection.
a
[L] Ratio 1.0:1...50.0:1, Inf:1
Sets the signal compression ratio
☞
Fx:003
Threshold [dB] –40...0dB
Sets the level above which the compressor is applied
☞
Fx:003
b
[L] Attack
Sets the attack time 1...100
☞
Fx:003
Release
Sets the release time 1...100
☞
Fx:003
c
[L] Gain Adjust [dB]
Sets the limiter output gain –Inf, –38...+24dB
☞
Fx:003
d
[E] Trim
Sets the parametric EQ input level 0...100
e
[E] Band1 Cutoff [Hz]
Sets the center frequency of Band 1 20...1.00kHz
Q
Sets the bandwidth of Band 1 0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 1 –18...+18dB
f
[E] Band2 Cutoff [Hz]
Sets the center frequency of Band 2 50...5.00kHz
Q
Sets the bandwidth of Band 2 0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 2 –18...+18dB
g
[E] Band3 Cutoff [Hz]
Sets the center frequency for Band 3 300...10.00kHz
Q
Sets the bandwidth of Band 3 0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 3 –18...+18dB
h
[E] Band4 Cutoff [Hz]
Sets the center frequency for Band 4 500...20.00kHz
Q
Sets the bandwidth of Band 4 0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 4 –18...+18dB
i
Routing LMT → PEQ, PEQ → LMT
Switches the order of the limiter and parametric EQ connection
j
Wet/Dry Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Src Off...Tempo
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance –100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Routing
Limiter
Trim
Parametric 4Band EQ
Limiter
Gain Adjust
Envelope - Control
a
[L] Ratio 1.0:1...50.0:1, Inf:1
Sets the signal compression ratio
☞
Fx:003
Threshold [dB] –40...0dB
Sets the level above which the compressor is applied
☞
Fx:003
b
[L] Attack
Sets the attack time 1...100
☞
Fx:003
Release
Sets the release time 1...100
☞
Fx:003
c
[L] Gain Adjust [dB]
Sets the limiter output gain –Inf, –38...+24dB
☞
Fx:003
d
[F] LFO Frequency [Hz]
Sets the LFO speed 0.02...20.00Hz
LFO Waveform
Selects LFO Waveform Triangle, Sine
e
[F] Delay Time [msec]
Sets the delay time 0.0...50.0msec
Depth
Sets the depth of LFO modulation 0...100
Feedback
Sets the feedback amount –100...+100
☞
Fx:020
f
[F] EQ Trim
Sets the EQ input level 0...100
g
[F] Pre LEQ Gain [dB]
Sets the gain of Low EQ –15...+15dB
Pre HEQ Gain [dB]
Sets the gain of High EQ –15...+15dB
h
[F] Cho/Flng Wet/Dry –Wet...–2:98, Dry, 2:98...Wet
Sets the effect balance of the chorus/flanger
☞
Fx:010, 020
Output Mode Normal, Wet Invert
Selects the output mode for the chorus/flanger
☞
Fx:067
i
Routing LMT → FLNG, FLNG → LMT
Switches the order of the limiter and chorus/flanger connection
☞
Fx:067
j
Wet/Dry Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Src Off...Tempo
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance –100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Routing
Chorus/Flanger
Feedback
Cho/Flng Wet / Dry
Normal
Wet Invert
Output Mode
–
+
Limiter
Limiter
Gain Adjust
Envelope - Control
LEQ HEQ EQ Trim
Chorus/Flanger
LFO: Tri / Sine