KORG Triton Studio - Manual (Page 4)

Program
Combination
Sequencer
Sampling
Song Play
Global
Disk
Ef
fect
Appendices
v
2. Combination mode. . . . . . . . . 33
Combination P0: Play ................................... 33
Select and play combinations.
0–1: Prog. Select Select a program for each timbre ........... 33
0–2: Mixer Specify pan and level ............................... 35
0–3: Arpegg. A Select an arpeggio pattern and make
settings for arpeggiator A
....................... 36
0–4: Arpegg. B Select an arpeggio pattern and make
settings for arpeggiator B
........................ 36
0–5: Sampling Perform sampling; make audio input
settings etc.
................................................ 36
Combination P1: Edit–Program/Mixer................ 37
Select the program for each timbre, and specify pan and
level.
1–1: Program/Mixer Specify program, pan, and level of each
timbre
........................................................ 37
Combination P2: Edit–Trk Param ..................... 38
Set various parameters for each timbre.
2–1: MIDI Channel Specify MIDI channel and status for each
timbre
........................................................ 38
2–2: OSC Make settings such as mono/poly and
portamento for each timbre
.................... 38
2–3: Pitch Make pitch-related settings such as
transpose and bend range for each timbre
.................................................................... 39
2–4: Other Make delay and scale settings for each
timbre
........................................................ 40
Combination P3: Edit–MIDI Filter ..................... 40
Specify MIDI message reception filtering for each timbre.
3–1: MIDI 1 Program changes, aftertouch etc. ........... 40
3–2: MIDI 2 Joystick, ribbon controller ....................... 41
3–3: MIDI 3 Realtime control knobs ............................ 41
3–4: MIDI 4 SW1/2, foot controller etc. ...................... 41
Combination P4: Edit–Zone/Ctrl ....................... 42
Specify the key range and controllers for each timbre.
4–1: Key Z Specify the key zone sounded by each
timbre
........................................................ 42
4–2: Vel Z Specify the range of velocities sounded by
each timbre
................................................ 42
4–3: MOSS Setup Displayed if the EXB-MOSS option is
installed; set EXB-MOSS parameters
..... 43
4–4: Controller Specify the function of the [SW1] and
[SW2] keys, and B-mode functions of the
REALTIME CONTROLS [1]–[4] knobs
. 43
Combination P7: Edit–Arp...............................44
Make settings for arpeggiators A and B.
7–1: Setup Assign arpeggiators to each timbre .......44
7–2: Arpegg. A Select an arpeggio pattern and make
settings for arpeggiator A
.......................45
7–3: Arpegg. B Select an arpeggio pattern and make
settings for arpeggiator B
........................45
7–4: Scan Zone Specify the ranges of notes and velocities
that will operate the arpeggiator
............45
Combination P8: Edit–Insert FX ........................46
Specify the output bus for each timbre, and make insert
effect settings.
8–1: Routing Specify the output bus and master effect
send levels for each timbre
......................46
8–2: Insert FX Select insert effects, turn them on/off, and
make chain settings
..................................47
8–3: IFX 1 Parameter settings for IFX1 .....................47
8–4: IFX 2 Parameter settings for IFX2 .....................47
8–5: IFX 3 Parameter settings for IFX3 .....................47
8–6: IFX 4 Parameter settings for IFX4 .....................47
8–7: IFX 5 Parameter settings for IFX5 .....................47
Combination P9: Edit–Master FX ......................48
Make settings for the master effects and master EQ.
9–1: Master FX Select the master effects, turn them on/
off, and make chain settings
...................48
9–2: MFX 1 Parameter settings for MFX1 ..................48
9–3: MFX 2 Parameter settings for MFX2 ..................48
9–4: Master EQ Parameter settings for master EQ ..........48
About the Jump pages
The LCD screens shown here are the Jump pages for each
mode.
The Jump page is a page menu that lets you access the var-
ious pages within each mode.
Here’s how to access the Jump page, and select the desired
page.
• Press the [MENU] key to access the Jump page. In the
LCD screen, press the page that you want to select, or
press the numeric key [0]–[9] corresponding to the
number of the desired page. (
☞ BG p.16)
• Alternatively, you can hold down the [MENU] key and
press the numeric key [0]–[9] corresponding to the
number of the desired page.