255 appendices – KORG Triton Studio User Manual
Page 266
255
Appendices
The following table shows the operations that the TRITON
STUDIO will perform when control change messages are
received, and the relation between settings and controller
movements on the TRITON STUDIO
Any control change number (CC#00–95) can be
assigned as the B-mode function of a REALTIME CON-
TROLS knob. In this case, the transmitted values will all
be 0–127.
TRITON STUDIO operations
when control changes are trans-
mitted/received
CC# Control
Value
Function
0
Bank select (MSB)
0...127
bank select message MSB
*1
1
Modulation 1
0...127
corresponds to joystick movement in the +Y direction (Vertical upward)
2
Modulation 2
0...127
corresponds to joystick movement in the –Y direction (Vertical downward)
4
Foot controller
0...127
corresponds to when the assignable pedal function is set to Foot Pedal
5
Portamento time
0...127
portamento time
6
Data entry (MSB)
0...127
MSB of RPN and NRPN data
*2
7
Volume
0...127
volume
*3
8
Post insertion effect panpot
0...127
pan after the insertion effect
10
Panpot
0...127
pan
11
Expression
0...127
volume
*3
12
Effect control 1
0...127
corresponds to effect dynamic control source FXCtrl1
13
Effect control 2
0...127
corresponds to effect dynamic control source FXCtrl2
16
Ribbon controller
0...127
corresponds to ribbon controller operation
17
Knob modulation 1
0...127
corresponds to when Knob Mod.1 is assigned as the B-mode function of a
REALTIME CONTROLS knob
18
Controller (CC#18)
0...127
for control of Alternate Modulation or Effect Dynamic Modulation
*8
19
Knob modulation 2
0...127
corresponds to when Knob Mod.2 is assigned as the B-mode function of a
REALTIME CONTROLS knob
20
Knob modulation 3
0...127
corresponds to when Knob Mod.3 is assigned as the B-mode function of a
REALTIME CONTROLS knob
21
Knob modulation 4
0...127
corresponds to when Knob Mod.4 is assigned as the B-mode function of a
REALTIME CONTROLS knob
32
Bank select (LSB)
0...127
LSB of bank select message
*1
38
Data entry (LSB)
0...127
LSB of RPN or NRPN data
*2
64
Damper
0...127
damper effect
65
Portamento On/Off
0...63(Off), 64...127(On)
turn the portamento effect on/off
66
Sostenuto On/Off
0...63(Off), 64...127(On)
turn the sostenuto effect on/off
67
Soft
0...127
soft pedal effect
70
Sustain level
0...127
sustain levels of the filter EG and amp EG
*4
71
Filter resonance level
High pass filter cutoff frequency
0...127
0...127
resonance level of the filter
cutoff frequency of the high pass filter
*5
*4
72
Release time
0...127
release times of the filter EG and amp EG
*4
73
Attack time
0...127
attack times of the filter EG and amp EG
*4
74
Low pass filter cutoff frequency
0...127
cutoff frequency of the low pass filter
*4
75
Decay time
0...127
decay times/slope times of the filter EG and amp EG
*4
76
LFO1 speed
0...127
LFO1 speed
*4
77
LFO1 depth
0...127
pitch LFO1 intensity
*4
78
LFO1 delay
0...127
LFO1 delay
*4
79
Filter EG intensity
0...127
filter EG intensity
*4
80
Panel switch 1 On/Off
0...63(Off), 64...127(On)
corresponds to on/off when the SW1 function is set to SW1 Mod.
81
Panel switch 2 On/Off
0...63(Off), 64...127(On)
corresponds to on/off when the SW2 function is set to SW2 Mod.
82
Foot switch On/Off
0...63(Off), 64...127(On)
corresponds to on/off when the function of the assignable foot switch is set to
Foot SW
83
Controller (CC#83)
0...127
for controlling Alternate Modulation or Effect Dynamic Modulation
91
Effect 1 depth
0...127
send 2 level
92
Effect 2 depth
0(Off), 1...127(On)
turn insertion effect 1, 2, 3, 4, 5 on/off
*6
93
Effect 3 depth
0...127
send 1 level
94
Effect 4 depth
0(Off), 1...127(On)
master effect 1 on/off
*6
95
Effect 5 depth
0(Off), 1...127(On)
master effect 2 on/off
*6
96
Data increment
0
97
Data decrement
0
98
NRPN(LSB)
2
10
11
corresponds to the arpeggiator on/off switch
corresponds to the arpeggiator Gate control knob
corresponds to the arpeggiator Velocity control knob
*7
*7
*7
99
NRPN(MSB)
0
MSB of NRPN
100
RPN(LSB)
0
select the pitch bend range
*2
1
select Fine Tune
*2
2
select Coarse Tune
*2
101
RPN(MSB)
0
MSB of RPN